bing tracking image
Customer Service My Orders
Q & A Icon

Replacement Weld on Mount for Bulldog Swivel Jack # BD171401  

Updated 06/10/2020 | Published 06/08/2020

Question:

I have bent my weld on swivel jack mount. Snap ring and jack are fine. Do you have another weld on mount dor this jack?

0

Expert Reply:

For just the replacement mount for the Bulldog Swivel Jack # BD171401 you'd want the # F500242 and you'd be set.

expert reply by:
0
Jameson C
Ask The Experts a Question >>

Video/Article/FAQ this Question was Asked From

Article or Video
Q & A Icon

Continue Researching

Explore Expert Info Our Expert
on Trailer Jack

Videos

Help Articles

Expert Answers

Others Also Watched
A Closer Look at the Replacement Mounting Bracket for etrailer and Ram Snap Ring Swivel Jacks
The Low-Down on the Round Snap Ring Swivel Jack w/ Footplate
An In-Depth Look at the Round Snap Ring Swivel Jack w/ Footplate
Detailed Breakdown of the REPL Snap Ring for Swivel Trailer Jacks
Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
Curt T-Connector Vehicle Wiring Harness Review C56040
How to Choose a Trailer Brake Controller
Clean Up Your Trailer Wiring
Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
Curt Mounting Bracket for 4-Pole Flat Trailer Connector Review
Curt Class III Trailer Hitch Step-By-Step Install - 2026 Honda CR-V
Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
Others Also Read
Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)
Trailer Wiring Diagrams
Brake Controller 7- and 4-Way Installation Kit (ETBC7)
How to Measure for Trailer Hitch Drop
Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
How to Measure Your Trailer Wheel Bolt Pattern
How to Choose the Right Trailer Hitch Class
5 Things to Know About Weight Distribution Hitches
Trailer Lighting Requirements
The 5 Best Trailer Drop Hitches You Can Buy
Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
Is It Illegal to Leave My Hitch on My Truck?
Others Also Asked
Diameter of Mounting Bracket Hole on Round Snap Ring Swivel Jack

The diameter of the hole on the Round Snap Ring Swivel Jack #TJB-2001-Z you referenced comes with mounting bracket #TJB-MB which has a 2-1/2 inch outer diameter and 2-1/4 inch inner diameter. If your current mounting bracket has a hole of that…

view full answer...
Snap Ring Hole Size of Fulton Swivel Jack and Compatibility with Shelby Model 5756 Welded Plate

The Fulton Round, Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10" Lift - 1,200 lbs #FTJ12000101 has a pilot hole diameter of 2.313 inches and utilizes the Replacement Retaining Ring for Bulldog and Fulton Snap-Ring Jacks #FP908600 which…

view full answer...
Recommended Bolt-On 2,000 Pound Swivel Jack for Trailer

The Bulldog Round Snap-Ring Swivel Jack #BD151464 referenced in your question is indeed a weld-on trailer jack. It is designed to mount onto the Weld-On Bracket #F500242 with the Snap Ring #BD500241. For a similar trailer jack that uses a bolt-on…

view full answer...
Swivel Trailer Jack With 2-1/2" Opening for Snap Ring Mounting Bracket

For your application we have the 2K Bulldog Round, Snap-Ring Swivel Marine Jack #BD151464 which fits with the L-Bend Bracket #F500242 that has the 2-1/2" opening you mentioned (see attached photo) and secures using the Snap Ring #BD500241.

view full answer...
How To Remove The Snap Ring On The Bulldog Swivel Jack To Swap Out Mounting Brackets

They make snap ring pliers that are used to remove snap rings. It has two pins on the end that stick into the holes of the snap ring and when squeezed it will open up the ring enough to be removed. You might also try to use 2 regular pliers. With one…

view full answer...
Overall Retracted Height of Bulldog Trailer Jack Part #BD171401

The overall retracted height of the Bulldog jack part #BD171401 that you mentioned from bottom of the jack to the top of the handle is 15-1/4 inches.

view full answer...
Why Does 4-Pin Trailer Wiring Have 5 Wires

Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer which…

view full answer...
Replacement Jack Options For a NAPA Trailer Tongue Jack #8215214

Unfortunately, the only information I could obtain from NAPA regarding your 8215214 tongue jack is it is rated for a 5,000lb lift capacity, is 14-1/5" tall and has a top wind handle. The Bulldog #BD171401 is going to be the closest option but…

view full answer...
Determining Correct Snap Ring for 2007 Fleetwood Williamsburg Camper Jack

In order to find which snap ring you need you would have to measure the outer diameter of the snap ring bracket on your trailer frame. A part like the #DL22672 REPL Snap Ring for Swivel Trailer Jacks - 2-5/16" Inner Diameter will fit trailer…

view full answer...
Retaining Ring Diameter for Bulldog Swivel Jack

The snap ring on the Bulldog Round, Snap-Ring Swivel Jack #BD171401 is 2-5/16". We do offer the Replacement Swivel Snap Ring for Bulldog Jacks #BD500241 if you need a replacement.

view full answer...
Distance from Mounting Surface to Center of Jack Tube on Bulldog BD171401

The distance from the mounting surface to the center of the tube of the Bulldog Jack part #BD171401 measures 2-1/4 inches.

view full answer...
What Pipe Mount Could Pro Series Trailer Jack #PS1401140303 Fit

The Pro Series trailer jack part #PS1401140303 that you referenced is designed to fit on a pipe mount diameter of 2 inches so if that's the size you have now (it looks like you do) then yes, this would easily fit on the same mount for an easy…

view full answer...