Retaining Ring Diameter for Bulldog Swivel Jack

Question

Question:

What is the size of the retaining ring?

asked by: Analkumar S

0

Expert Reply:

The snap ring on the Bulldog Round, Snap-Ring Swivel Jack # BD171401 is 2-5/16".

We do offer the Replacement Swivel Snap Ring for Bulldog Jacks # BD500241 if you need a replacement.

expert reply by: Bud M

0

Answer 1

According to my research, the 2004 Tahoe is capable of being flat towed. Please check your owner's manual for confirmation and procedures. First your Tahoe will need base plates. I recommend Demco base plate kit, part #DM9518077. A good tow bar…

view full answer...

Answer 2

Fulton's snap-ring jacks like the #FTJ120W0301 are going to top out at 1,200lbs and the 1,500LB Jack #F141132 you found has a bolt-thru design and is not offered in a snap ring. We do offer the 2,000LB Jack #TJB-2002S-B which would fit your…

view full answer...

Answer 3

To verify fitment of the Bulldog Round, Snap-Ring Swivel Jack #BD151110 on your trailer you will need to measure the diameter of the Bracket #F500242 on your trailer. The diameter of the outer part of the bracket needs to be 2-1/2" for the…

view full answer...

Answer 4

You are correct, the Fulton Snap Ring, #FP908600, and Bulldog Snap Ring, #BD500241, are very similar. I went out to the warehouse and pulled both parts to measure them using digital calipers. Both had the following measurements: Inner diameter = 2.28…

view full answer...

Answer 5

In order to find which snap ring you need you would have to measure the outer diameter of the snap ring bracket on your trailer frame. A part like the #DL22672 REPL Snap Ring for Swivel Trailer Jacks - 2-5/16" Inner Diameter will fit trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Retaining Ring Diameter for Bulldog Swivel Jack

Featured Help Information

Miscellaneous Media

Continue Researching