Snap Ring Hole Size of Fulton Swivel Jack and Compatibility with Shelby Model 5756 Welded Plate

Question

Question:

What is the snap ring hole size on a Fulton FTJ12000101 jack? I am replacing a weld on Shelby Model 5756.

asked by: GREGORY S

0

Expert Reply:

The Fulton Round, Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10" Lift - 1,200 lbs # FTJ12000101 has a pilot hole diameter of 2.313 inches and utilizes the Replacement Retaining Ring for Bulldog and Fulton Snap-Ring Jacks # FP908600 which has an inner diameter of 2-5/16 inches. The Shelby model 5756 you referenced will work perfectly with this jack and snap ring.

expert reply by: Jason S

0

Answer 1

Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer which…

view full answer...

Answer 2

For your application we have the 2K Bulldog Round, Snap-Ring Swivel Marine Jack #BD151464 which fits with the L-Bend Bracket #F500242 that has the 2-1/2" opening you mentioned (see attached photo) and secures using the Snap Ring #BD500241.

view full answer...

Answer 3

The snap ring hole of the Pro Series Round, Snap-Ring Swivel Jack #PS1401140303 that you referenced that mounts on the trailer has an outer diameter of 2-1/2 inches.

view full answer...

Answer 4

I spoke with my contact at Dutton-Lainson and he gave me the dimensions of this Replacement Snap Ring #DL22672. Inner Diameter = 2.27 Thickness = .080 Outer Diameter = 2.625

view full answer...

Answer 5

The Pro Series trailer jack part #PS1401140303 that you referenced is designed to fit on a pipe mount diameter of 2 inches so if that's the size you have now (it looks like you do) then yes, this would easily fit on the same mount for an easy…

view full answer...

Answer 6

Unfortunately, the only information I could obtain from NAPA regarding your 8215214 tongue jack is it is rated for a 5,000lb lift capacity, is 14-1/5" tall and has a top wind handle. The Bulldog #BD171401 is going to be the closest option but…

view full answer...

Answer 7

You are correct, the Fulton Snap Ring, #FP908600, and Bulldog Snap Ring, #BD500241, are very similar. I went out to the warehouse and pulled both parts to measure them using digital calipers. Both had the following measurements: Inner diameter = 2.28…

view full answer...

Answer 8

A snap ring like #FP908600 can be measured using a set of dial calipers or digital calipers to get the most accurate measurement possible. To measure the inside diameter, on the inside of the rind measure across at the widest point (not at the bottom…

view full answer...

Answer 9

For just the replacement mount for the Bulldog Swivel Jack #BD171401 you'd want the #F500242 and you'd be set.

view full answer...

Answer 10

They make snap ring pliers that are used to remove snap rings. It has two pins on the end that stick into the holes of the snap ring and when squeezed it will open up the ring enough to be removed. You might also try to use 2 regular pliers. With one…

view full answer...

Answer 11

The best solution would be to replace the handle on your existing Bulldog Jack, #BD171401. You will need Replacement Topwind Handle for Bulldog Round Jacks, #BD500180. I did speak with my contact at Reese and Bulldog and he stated that the internal…

view full answer...

Answer 12

The snap ring on the Bulldog Round, Snap-Ring Swivel Jack #BD171401 is 2-5/16". We do offer the Replacement Swivel Snap Ring for Bulldog Jacks #BD500241 if you need a replacement.

view full answer...

Snap Ring Hole Size of Fulton Swivel Jack and Compatibility with Shelby Model 5756 Welded Plate

Featured Help Information

Miscellaneous Media

Continue Researching