Is 8 inches From Bottom of Weight Distribution System to Ground Enough Clearance
Updated 04/08/2019 | Published 04/06/2019
Question:
I recently purchased this shank in order to achieve a 3-1/2” drop, which is what I need for my trailer. At this height, the bottom of the shank sits approximately 8” off the ground. I now drag the shank on the ground when I back out of my driveway, unless I cut it really sharp, at an angle. Is this height safe for a road trip?
asked by: Chris R
Expert Reply:
Eight inches from the ground to the bottom of your weight distribution shank would be fine for most situations but like you've experienced turning into inclined driveways can cause it to drag. Your trailer must sit pretty low to call for your shank setup to sit that low. It might be worth looking into raising your trailer suspension so that your shank settings could be a bit higher.
Product Page this Question was Asked From
Fastway e2 Weight Distribution Shank - 12" Long - 10-1/4" Rise, 5-1/2" Drop - 1.2K TW
- Accessories and Parts
- Weight Distribution Hitch
- Shanks
- 1100 lbs TW
- Fits 2 Inch Hitch
- e2
- Round - 7 Inch Drop
- Trunnion - 5 Inch Drop
- Round - 10 Inch Rise
- Trunnion - 10 Inch Rise
- Fastway
more information >
Continue Researching
- Video: An In-Depth Look at the Curt MV Weight Distribution System
- Shop: Trailer Hitch
- Q&A: How to Determine if 1/2 inch Shaft or 5/8 inch Shaft Spool Roller is Needed for Boat Trailer
- Search Results: class 4 trailer hitch
- Search Results: curt weight distribution hitch
- Q&A: Hitch Extender Recommendation Towing 7,500 lb Trailer
- Q&A: Best Weight Distribution Hitch For 450 lb and 750 lb Tongue Weights
- Q&A: Weight Distribution Hitch With Sway Control Recommendation For 600 lb Tongue Weight
- Shop: Equal-i-zer Weight Distribution Shank - 2-1/2" Hitch - 12" Drop
- Shop: TorkLift SuperHitch Magnum Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2" and 2"
- Shop: Curt MV Weight Distribution System - Round Bar - 10,000 lbs GTW, 1,000 lbs TW
- Shop: Adjustable Width Trailer Hitch Receiver for RVs, 18" to 51" Wide
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Video: How to Choose a Trailer Brake Controller
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Shop: Suspension Enhancement
- Search Results: brake controller
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: How to Measure for Trailer Hitch Drop
- Shop: Brake Controller
on Accessories and Parts
