2014 Ford E350 Van Trailer 4-Way Trailer Wiring Kit

Question

Question:

Hi, Im wondering what wiring kit will work with our 2014 Ford E350 van. It appears as though theres already a place to plug in a trailer wiring kit at the back of the van. If you could let me know what kit works for our van would be fantastic,

asked by: Eric M

0

Expert Reply:

We have the Hopkins 4-way part # HM11140665 which is designed to fit the square connector you send in a picture of that would work well for you.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Hopkins Wiring harness part #HM11140665 that you referenced would be the correct wiring kit for your Ford E350 as long as it is a 2009-2014 model.

view full answer...

Answer 2

On your 2013 Ford E-350, the factory brake controller port should be located beneath the dash, taped to another harness behind the emergency brake. I have attached an installation video on an earlier model Ford Van that will be similar to your…

view full answer...

Answer 3

Since you don't have any existing wiring on your 2013 E-350 you'll need to start by adding a 4 way, which I recommend using the Hopkins Plug In Simple #HM11140495. This will provide you with the base wiring needed to then add a 7 way…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

2014 Ford E350 Van Trailer 4-Way Trailer Wiring Kit

Continue Researching