Reinstalling Exhaust Hanger on Lincoln Town Car After Installation of Trailer Hitch
Updated 10/29/2018 | Published 10/27/2018
Question:
Hi I recently purchased a 13707 hitch and installed it on a 2010 lincoln town car. Am having a bit of a problem getting the exhaust hanger installed on the right side. do you have any videos of picture instructions on how to get this correct. The 13707 went well. the left front is tight but turns when i try to tighten it more appreciate your direction.
asked by: Paul H
Helpful Expert Reply:
There is a video of Curt Trailer Hitch # 13707 being installed on a Lincoln Town Car which I have linked for you; this is an install on a 2003 Town Car but the process will be the same as your 2010.
As per the linked installation instructions, a portion of which I have cut out for you to look at, states you need to rotate the bumper hanger, reattach the hanger bracket and then attach the hanger assembly to the hitch mounting plate and exhaust.
You will need to use washers to level the exhaust hanger on the plate; if you go to about the 6:40 mark of the linked install video you will be able to view how this is done.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Search Results: trailer wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Wiring
- Q&A: What Additional Steps Are Required For Installation Of The Curt Receiver # 13707 on Dual Exhaust?
- Q&A: Hitch and Trailer Wiring Harness Recommended for 2010 Mercury Grand Marquis
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Article: Trailer Hitch Installation Tips
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: Curt Powered Tail Light Converter Installation - 2023 Kia Telluride
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer jack
- Shop: Brake Controller
- Video: Clean Up Your Trailer Wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
on Trailer Hitch
