How Long is the Cord # H20043?

Question

Question:

How long is this cord? Do you sell any coiled versions?

asked by: Ben H

0

Expert Reply:

The Bargman 7-Way Molded Trailer Wire Connector # H20043 is 4 feet long.

We also have the coiled 6 foot # WG54006-043 and the coiled 12 foot # WG54006-046 if you prefer a coiled cord.

expert reply by: Jason S

0

click to enlarge

Answer 1

After speaking to my contact at Redline, I have found the thickness of the Redline Grease Seal #1105-100-035 you referenced is .3 inches.

view full answer...

Answer 2

Though we do have the replacement bearings, races, and seals available for your Hadco 3109 hub (which I have listed below), the combination used will not have an equivalent replacement hub available, unfortunately. Replacement Trailer Hub Bearing…

view full answer...

Answer 3

Stretching the 7-Way Trailer Connector #WG54006-043 to 6 feet isn't the best option for you. It'll reach 6 feet but the coils are fairly tight. I extended it easily to about 4 feet but beyond that it wanted to fight me. It'll loosen up…

view full answer...

Answer 4

We do have a selection of fenders for 13" wheels that you can use to replace your current fenders. Among our linked selection we have different constructions like aluminum, plastic, and steel. These fenders can mount via brackets or welding…

view full answer...

Answer 5

You will want to confirm but the Titan hubs on your boat trailer could possibly be compatible with electric brakes. You will want to inspect the inner surface. If it is flat and smooth you can use it for electric brakes. For your brakes you are going…

view full answer...

Answer 6

You can convert your trailer to electric over hydraulic brakes by using hydraulic trailer brakes, hydraulic drums, hydraulic brake lines, and adding an electric over hydraulic actuator like the HydraStar Electric Over Hydraulic Actuator for Drum…

view full answer...

Answer 7

Hi Steve; I would use 10 gauge wire #10-1-1 for the brakes instead of 12 gauge. The same butt connectors #DW05745-10 will still work. If you're connecting 3 wires together I would either use a wire nut with plenty of electrical tape or solder…

view full answer...

Answer 8

In most cases, you can just simply add brakes to the existing axle and you don't need an entire new axle. That said, this is all based on the axle capacity and I don't have any way to look this up for you. If you have a 3,500 lb axle for…

view full answer...

Answer 9

The measurements from your spindle and hub line up with the HADCO seal #1105-100-035 that you were looking at. This will work as a replacement to your seal on your axle. Sounds like you were looking for a rubber coated one like the one that was…

view full answer...

Answer 10

It sounds like you need an extension with two 7-blades on it, but in order to do this you will need to get a plug and lead as well as a plug. So you will need the 7-Way Molded Trailer Wire Connector #H20043 (4 feet long) or the coiled Bargman…

view full answer...

Answer 11

The reason that 10 Gauge #10-1-1 or 12 Gauge #12-1-1 wire is recommended for 10" brake assemblies, like part #AKEBRK-35-SA, is because they pull more power than the lights on your trailer. I believe the green wire you are referring to carries…

view full answer...

Answer 12

The Universal Wiring Kit #ETBC7 that you referenced is indeed what you need to install a fully functional 7-Way on your 1996 Isuzu Trooper so that you can install the Tekonsha Prodigy P2 Brake Controller #90885 to power the trailer's electric…

view full answer...

How Long is the Cord # H20043?

Continue Researching