Width of Redline Grease Seal # 1105-100-035

Question

Question:

I am making up a seal system for a customer. I need a low profile seal, and these look pretty thin. What is the measured thickness? Thanks

asked by: Ed

0

Expert Reply:

After speaking to my contact at Redline, I have found the thickness of the Redline Grease Seal # 1105-100-035 you referenced is .3 inches.

expert reply by: Brandon M

0

click to enlarge

Answer 1

Though we do have the replacement bearings, races, and seals available for your Hadco 3109 hub (which I have listed below), the combination used will not have an equivalent replacement hub available, unfortunately. Replacement Trailer Hub Bearing…

view full answer...

Answer 2

The measurements from your spindle and hub line up with the HADCO seal #1105-100-035 that you were looking at. This will work as a replacement to your seal on your axle. Sounds like you were looking for a rubber coated one like the one that was…

view full answer...

Answer 3

The yellow wire of the 7-way harness part #H20044 that you referenced goes to the center pin of the 7-way which is an aux circuit that is typically used for reverse lights if present on the trailer. Normally the red wire on a 7-way (RV standard…

view full answer...

Answer 4

The Bargman 7-Way Molded Trailer Wire Connector #H20043 is 4 feet long. We also have the coiled 6 foot #WG54006-043 and the coiled 12 foot #WG54006-046 if you prefer a coiled cord.

view full answer...

Answer 5

For your 3109 grease seals, you can use the Grease Seal #1105-100-035 for replacements. This grease seal has the same measurements (2" I.D. | 2.875" O.D.) as your current seal and has a thickness of .3".

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Width of Redline Grease Seal # 1105-100-035

Product Page this Question was Asked From

Continue Researching