Is Drilling Required to Install CURT Trailer Hitch # C15445 on a 2011 Ford F-350 Cab and Chassis

Question

Question:

Does this hitch require I DRILL holes in the frame, or does it bolt to existing holes?

asked by: Joe S

0

Expert Reply:

Hello Joe.

To install the CURT Trailer Hitch, # C15445, on a 2011 Ford F-350 Cab and Chassis only model, you will need to drill two holes in the frame using a 9/16 inch drill bit. These holes are for the forward most attachment points on the vehicle. I have included a link to the installation instructions for you.

expert reply by: Kate F

0

Answer 1

The Curt Trailer Hitch Receiver part #C15445 which is a fit for a Ford F-Series Cab and Chassis has a drop of 5-1/2" when measuring from the top of the mounting flange or bottom of the frame to the top cross tube. I have attached a photo of this…

view full answer...

Answer 2

I went out to the warehouse and pulled Curt Class V Trailer Hitch #C15300 and took some measurements for you. From the front bolt hole to the rivet (center to center) is 1-5/16 inches. From the rivet to the rear bolt hole is 7-7/8 inches and the…

view full answer...

Answer 3

I went out to the warehouse and measured the CURT Trailer Hitch, #14301. Starting with the front to back measurements of the holes on the same side, from the first hole, nearest the back of the vehicle to the center hole measures 6-1/2 inches on…

view full answer...

Answer 4

The CURT Trailer Hitch Receiver #C15445 that you referenced should work well for your 2014 Ford F350 Cab and Chassis as this hitch is confirmed to fit all model 2014 Cab and Chassis F350s. As long as your fuel tank is in the factory location you…

view full answer...

Answer 5

Thanks for reaching out, Andrew! The best solution for adding a hitch to your bus is the Curt Class 5 Universal Weld-on Hitch w/ Brackets #C99CR since there aren't any custom options for your bus. Since this is a weld-on installation you'll…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver #C15320 is 40-1/4" across and from the top to the top of the crosstube measures 1-15/16". This hitch is only a fit for certain model year Chevy Express and GMC Savana cargo and passenger vans.

view full answer...

Answer 7

Hi Chris; the distance across the #C14011 from bolt hole to bolt hole is 34.49" on center. According to Curt, it is the same for all four sets of bolt holes. This hitch is designed to fit the 2000 - 2005 Ford Excursion.

view full answer...

Answer 8

The Curt XD Class V Hitch #C15324 that you referenced is indeed a correct fit for your 2006 Chevrolet Avalanche. I visited our warehouse to obtain the measurements you requested. The hitch mounting flanges measure 10-11/16-inches long x 2-1/4-inches…

view full answer...

Answer 9

I checked with Curt and they sent me the following dimensions based on your picture for the #C15410. Red line measurement 10.55” Yellow Line measurement 5.32” Green Line measurement is 7.5”

view full answer...

Answer 10

The Curt Trailer Hitch Receiver #C15410 has a measurement of 12-1/2" from the face of the receiver to the bolt hole nearest the receiver. I have attached a picture showing the dimensions for the bolt holes as well as the receiver distance. The…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Is Drilling Required to Install CURT Trailer Hitch # C15445 on a 2011 Ford F-350 Cab and Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching