Distance Across Curt Hitch From Bolt Hole to Bolt Hole

Question

Question:

What are the dimensions from bolt hole to bolt hole? Left to right

asked by: Chris

0

Expert Reply:

Hi Chris; the distance across the # C14011 from bolt hole to bolt hole is 34.49" on center. According to Curt, it is the same for all four sets of bolt holes. This hitch is designed to fit the 2000 - 2005 Ford Excursion.

expert reply by: Robin H

0

Curt 14011
(click to enlarge)

Robin H.

1/12/2026

Hey Chris, did the 34.49-inch bolt hole spacing on the Curt hitch line up with your Excursion’s frame? Knowing how the fit turned out could help others checking their measurements too.

Answer 1

I went out to the warehouse and pulled Curt Class V Trailer Hitch #C15300 and took some measurements for you. From the front bolt hole to the rivet (center to center) is 1-5/16 inches. From the rivet to the rear bolt hole is 7-7/8 inches and the…

view full answer...

Answer 2

I went out to the warehouse and measured the CURT Trailer Hitch, #14301. Starting with the front to back measurements of the holes on the same side, from the first hole, nearest the back of the vehicle to the center hole measures 6-1/2 inches on…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver #C15320 is 40-1/4" across and from the top to the top of the crosstube measures 1-15/16". This hitch is only a fit for certain model year Chevy Express and GMC Savana cargo and passenger vans.

view full answer...

Answer 4

Thanks for reaching out, Andrew! The best solution for adding a hitch to your bus is the Curt Class 5 Universal Weld-on Hitch w/ Brackets #C99CR since there aren't any custom options for your bus. Since this is a weld-on installation you'll…

view full answer...

Answer 5

Hello Joe. To install the CURT Trailer Hitch, #C15445, on a 2011 Ford F-350 Cab and Chassis only model, you will need to drill two holes in the frame using a 9/16 inch drill bit. These holes are for the forward most attachment points on the vehicle.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Distance Across Curt Hitch From Bolt Hole to Bolt Hole

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching