Replacement Trailer Hub for EZ Loader Boat Trailer with 2K Axle
Updated 09/12/2018 | Published 09/10/2018
Products Featured in This Question
Question:
I have an 1989 EZ Loader boat trailer. Im not sure of weight capacity... It is a roller trailer with 5 4 1/2 bolt pattern. The tire rim diameter is 13 with the tire its approximately 20.5. I have a 16 Lund aluminum fishing boat on the trailer. The VIN # is 1ZE1MCU1XKE016917 I am looking for 2 new pre-greased replacement hubs 1 to replace existing, 1 for road spare. Im not sure about the spindle and dont want to disassemble until I have the new hubs...
asked by: Mitchell
Expert Reply:
I did some research on your EZ Loader Boat Trailer and found out that you have part # L44649 bearings which means the Trailer Hub Assembly part # 8-258-50UC1-EZ is the best option we have for you. However, the grease seal included with this hub is not correct nor do we have the correct one (12194TC) for you therefore you would need to obtain this elsewhere. This hub does not come pre-greased and we do not have any with these bearings that are but we do have the Bearing Packer part # PTW1218 which is very simple to use.
Product Page this Question was Asked From
Replacement Trailer Wheel Bearing - L44649 - Qty 1
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.06 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Shop: Trailer Hitch
- Search Results: ez loader hub
- Q&A: Trailer Hitch Receiver Needed for 2001 Chevy S-10 Xtreme Trim
- Video: An In-Depth Look at the CE Smith Trailer Hub Assembly w/ Carrying Case for 3,500-lb Axles
- Video: Detailed Breakdown of the Kodiak Trailer Hub for 5,200-lb to 6,000-lb Axles
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: How to Pick Out Replacement Hubs for a Boat Trailer
- Q&A: Is Weight Capacity Listed On Trailer Hubs The Capacity Of The Trailer Or Axles
- Shop: DeeMaxx Trailer Idler Hub for 6,000-lb Axles - 6 on 5-1/2 - Threaded - Galvanized
- Q&A: How To Figure Out the Correct Replacement Hubs for a EZ Loader Boat Trailer
- Q&A: Do You Have Replacement Hubs for a 2009 EZ Loader Boat Trailer?
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Video: How to Choose a Trailer Brake Controller
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Shop: Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer jack
- Video: Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
on Trailer Bearings Races Seals Caps
