Distance Between Mounting Holes Left to Right of Curt Hitch # C15300

Question

Question:

How far apart are the holes?

asked by: Mark R

0

Expert Reply:

The distance between the mounting holes from left to right on the Curt hitch part # C15300 that you referenced is 35-7/16 inches.

expert reply by: Jameson C

0

Answer 1

The Hole spacing for the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25198 are as follows(all measurements are for center of hole to center of hole). 34" Width Frame -Front holes- 28-7/8" -Middle and rear holes- 29-1/2"…

view full answer...

Answer 2

I have attached a photo of the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25198 you asked about. I have noted the mounting holes on the photo you can check out. The distance center-to-center from the front mounting hole to the second is…

view full answer...

Answer 3

It looks like you're asking about the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25122, for your 1996 Ford F-150. You didn't say exactly which dimensions you're looking for but I went out to the warehouse and measured the…

view full answer...

Answer 4

I spoke with my contact at Curt to obtain the mounting bolt hole locations for the Trailer Hitch Receiver, #C15300 on a 1993 Ford F-150. I have attached a picture to illustrate these measurements. As for repositioning the spare tire, you may need to…

view full answer...

Answer 5

What you will want to do is measure the distance between the mounting holes on the frame of your truck to see if the Curt hitch part #C15300 will fit. If the holes are 36 inches apart on center then this hitch will fit and work well.

view full answer...

Answer 6

The rattle or play you experienced is very common and the solution isn't to replace the ball mount with a tighter fitting one as that's not really possible but is to use an anti-rattle device like the part #63232. This installs in the shank…

view full answer...

Answer 7

When measuring the frame width on a vehicle, you will need to measure from the outside of one frame rail to the outside of the other frame rail. It sounds like you have the 37-1/4 inch frame on your 1983 Ford F-100. The Curt Class IV 2 Inch Hitch,…

view full answer...

Answer 8

The Curt Trailer Hitch Receiver #14001 for your 1995 Ford F-150 is only designed to fit the stock truck. I looked and could not find if the 38 gallon oversized tank was OEM or an OEM option, so if it is aftermarket, I can't guarantee a fit for…

view full answer...

Answer 9

Thank you for the photo! What you have there is a deep drop or "cowboy" bumper. So, for a 2 inch trailer hitch that is confirmed to fit your 1989 Ford F-250 XLT Lariat with the deep drop bumper, I recommend the Curt #C15511. This 3-piece…

view full answer...

Answer 10

I contacted Draw-Tite about the Class III Max-E-Loader Trailer Hitch, item #41004. Draw-Tite informed me that the measurement they have is 5-3/4 inches from the mounting location to the top of the receiver tube that the drawbar slides into. I do have…

view full answer...

Answer 11

A high boy is a generic term used to encompass all Ford F-250 4x4 trucks from the late 1960s to the late 1970s (circa 1967 to 1977 and a half). If your 1976 is an F-250 with 4 wheel drive, it falls under the high boy umbrella. F-100 and F-150 models…

view full answer...

Answer 12

The distance from the front hole to the middle on the #14001 is 5.2". From the middle to the rear hole is 4.04" and from the front hole to the rear hole is 9.2". The distance across for each set of mounting holes is 36".

view full answer...

Distance Between Mounting Holes Left to Right of Curt Hitch # C15300

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching