Bearing Replacement for Load Rite 1.06? – STRAIGHT SPINDLE Kit

Question

Question:

Im trying to find a comparable kit to this: BEARING KIT- 1.06? – STRAIGHT SPINDLE loadrite

asked by: TJ

0

Expert Reply:

I found the bearing kit you referenced from Load Rite and it is a split between a BTR spindle where the bearings ride which means you'd need the bearings # L44649 and races # L44610 and a seal of # 34823 and you'd be set.

expert reply by: Jameson C

0

Answer 1

There are two different bearing combinations commonly used on 2000lb trailer axles, so determine which hub assembly will be correct for your trailer you will need to confirm which bearing combination your trailer has. The easiest way to do this is to…

view full answer...

Answer 2

The hub ratings are for the axle capacity, and not the trailer weight capacity. For example, The trailer hubs you came from, part #AKIHUB-545-35-EZ-K is designed for 3,500 lb axles. This hub includes the bearings races, seals, grease cap, and lug…

view full answer...

Answer 3

The bearing kit that contains a 1.06" outer bearing, 1.38" inner bearing, and Dexter 010-004-00 Grease Seal is the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles part #BK2-100. This is a very common bearing kit for Dexter and Lippert…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Bearing Replacement for Load Rite 1.06? – STRAIGHT SPINDLE Kit

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching