Recommended Trailer Hitch Receiver for 1979 Chevy C10 Truck with Roll Pan Bumper

Question

Question:

I have a roll pan on my 79 C10 short bed. What hitch receiver can I use for it?

asked by: Fern

0

Expert Reply:

For your 1979 Chevy C10 short bed with roll pan bumper, I recommend the Curt Trailer Hitch Receiver # 13028. Although the receiver will stick out further as it is intended for the standard bumper, I've attached a photo of similar C10 with the roll pan bumper that has this hitch installed. This trailer hitch will require drilling for installation.

expert reply by: Jason S

0

click to enlarge

Answer 1

The Curt Trailer Hitch Receiver part #13028 is designed to fit the following vechiles: - 88-91 CHEVY/GMC 4 DR CREW CAB ONLY - 73-79 FORD 250 CREW CAB - 73-06 CHEVY/GMC FULL SIZE CAB & CHASSIS w 34" FRAME - 73-06 FORD PICKUP: CAB AND CHASSIS…

view full answer...

Answer 2

Hey Kevin, Thanks for your question! The B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2" #BWHDRH25122 measures 5.4 inches from the top of the frame mounting brackets to the top of the receiver tube. Of all the hitches we…

view full answer...

Answer 3

Hey Mark! For a rating that high that will fit your motorhome you're going to have to switch to a weld-on hitch. The Curt Class 5 Universal Weld-on Hitch #C99CR is going to be the best option here. This hitch still has a 2" receiver and…

view full answer...

Answer 4

Hey Debra, The great thing about the Draw-Tite hitch spare tire carrier #6715 is that it is universal! Meaning it will fit any bolt pattern and tire size. I have had people use this with that same bolt pattern with no issues. The one thing to keep in…

view full answer...

Answer 5

The Curt Trailer Hitch Receiver part #13028 could potentially fit your 1966 Chevrolet C10 with aftermarket bumper. However, I would not be able to confirm this as the trailer hitch is only tested with the OEM bumper. I have attached a photo for you…

view full answer...

Answer 6

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 7

Hey Wes, the hitches for deep drop bumpers like the part #C15511 have a drop of 8 inches from the frame surface of the truck down to the top of the hitch opening. The fits for standard bumpers like the #13028 have a drop of 4-1/2 inches. I attached…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Recommended Trailer Hitch Receiver for 1979 Chevy C10 Truck with Roll Pan Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching