To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Average Customer Rating: 4.6 out of 5 stars (171 Customer Reviews)
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Fits my 1966 C10, perfectly.
Perfect fit on my 1966 Chevy C10
Well made product, easy straight forward installation
Unfortunately, UPS delivered the package to the wrong address. i've contacted them, and hope they can resolve the matter.
Great quality and a great price! Made in USA.
A very great Hitch easy install and works great very well built.It bolted up to my 1955 second series chevy truck perfectly after drilling holes. Thank you for a great product.
Superb service doesn’t do justice folks like y’all are a dying breed
Haven’t installed yet but will send pictures when I do
I have never seen follow up emails on an internet purchase
You sold me a hitch and some HOPE thank you
The quality of the CURT hitch is superb. Installation was s bit strange. One hole on each side lined up. I had to drill the other four. Not a big deal. The weird part is that the center section of the bumper where the license plate goes had to have 3/4 inch cut from the bottom and the license moved up 3/4 inch to clear the receiver.
Someone without a good workshop would not have been able to install this hitch.
This pic is before the license was moved up.
I have not installed yet, but appears to be a very solid and well built hitch. Came with instructions and hardware to install on my 66 C-10.
James
4/16/2024
Hitch has been great. It is on my 66 Chevy C-10. I had to remount my spare as the hitch got in the way, but that was no big deal
Installed on my 69 GMC. I was able to oblong two of the existing holes in the rear but have to drill the other 4 holes. I added a frame mounted tank for EFI and this did not interfere. The spacers go between the frame and hitch due to factory rivets. All good!
Installed this on my 69' C-10 LWB about 1yr ago and have had very good success with it. As I recall it was a little more difficult because I set it forward a little more than normal and had to drill a couple holes. It wound up being almost a hidden hitch. Hitch appears to be well built with good looking welds. I have used this to tow 22' Ski boat on numerous occasions without any issues.
Byron
6/18/2020
After another year the hitch is still performing as it should with no issues.
Just as most of the other reviews have said, the hitch is nice but it does require removal of about 3/4” off the bottom of the license plate bracket. Only two hole holes lined up and you have to either drill them out or weld on. Other than that it’s a nice hitch
Fit my 1984 K10 Chevy short bed great! Fairly easy install.
Brooke M.
12/4/2024
Looks sharp!
First let start off by saying that from the time I ordered the hitch receiver, and the time it arrived at my doorstep was quite timely and much faster than other sites I have ordered parts from. Directions were simple enough to understand and not much of a read. Only problems I came across was the previous holes that were drilled into the frame did not match with the holes on the receiver (previous owner must have had a different style receiver installed). I wasn’t too upset at this as this was something I expected from a truck that is nearly 50 years old; simply fixed this by drilling new holes, which if I remember correctly, was stated to be expected during install. Along with this, I had to remove the exhaust tail pipes as they were in the way, but this shouldn’t be a problem if your vehicle has the exhaust directed out the side instead of straight back like mine. The directions state to use a 1/2 inch drill bit for the holes, but I found this to be too tight. I would recommend using a 5/8 inch bit or shimmying the 1/2 inch bit around while you drill. I would recommend you get a buddy to help, but in a case like mine, simple vice grips sufficed to hold the hitch receiver in place while I drilled. Should take about an hour with help and sharp drill bits. Overall was a good experience.
Product and hardware are of good quality, only 1 hole on each side of my trucks frame lined up, so I had to drill more holes in the frame and line it up the best I could, also it didn’t clear the license plate frame on the bumper so I had to trim that about an inch, but in the end it looks good and feels secure, so I’m happy, I haven’t towed with it yet but I torqued the bolts up with a breaker bar so I’m sure it will be fine for a small boat.
Heather A.
7/28/2018
When installing a trailer hitch like part # 13028 it is necessary to use a torque wrench to get the bolts to the right tightness. It is important to tighten bolts to the specified foot lbs in the instructions to avoid failure. Many auto parts stores lend out tools so you will not have to buy one in most cases.
Like everything Curt makes, this receiver has excellent build quality. It arrived faster than I thought it would
Installed on my 86 Chevy C10. Had to modify a few things but not terrible. There were some brackets that connected the bumper to the frame that needed to be removed. I took a picture of the bracket loosely attached for reference. Also had to drill out some rivets in a piece of metal that connects the two frame rails. I took a picture of me pointing at the spot where the rivet was. So had to drill 4 holes total. Overall not too difficult and is pretty well hidden under the truck.
With the help of my brother the job went smooth. Be sure to follow instructions as to the direction of bolts. Had a slight interference with license plate but made a simple modification.
Nice high quality, easy to install, fast shipping, would recommend this hitch for 67-72 C10 truck. Exact fit to frame, and even used 2 existing holes. If hitch was made about 1 inch narrower would not even require any drilling. Thank you.
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
David
3/14/2021
Awesome. I have pulled a 14 box trailer with my 67 Chevy C10 several times. No issues at all.