Installation and Details of Optronics Mini LED Lights # MCL11CRKB
Updated 09/06/2011 | Published 09/02/2011
Question:
I just learned about these new leds on your site. Do you have installed photos of the product? or video? It says they are recessed, so is it only the lens cover that sticks out and the black ring is the grommet? or is there a black ring sticking out as well as the clear lens, and then a black nut on the inside you tighten? how bright are these? I love how compact these are, but would love to see one better, before committing to ordering a bunch. Looking forward to your answer.
asked by: Frank D
Expert Reply:
I contacted our representative at Optronics about the Mini LED Lights, part # MCL11CRKB. I have attached a side angle view of this light that our representative at Optronics sent. At this time we do not have installed pictures of the light or a video of the light.
The lens cover sticks out slightly as you can see from the picture and the black ring is the grommet. To install, you will need to have an 11/16 inch hole drilled to insert the grommet. Then, the light pushes into the grommet for a snug fit.
Since this is an LED light, it will burn brighter than an incandescent light. The advantage of LED lights is that they do burn brighter, but they also draw less power than traditional incandescent lights.
Product Page this Question was Asked From
Uni-Lite LED Clearance and Side Marker Light w Grommet - Submersible - 2 Diodes - Clear Lens - Red
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Round
- Recessed Mount
- Submersible Lights
- LED Light
- 3/4 Inch Diameter
- Red
- Optronics
more information >
Continue Researching
- Q&A: What Is The Amp Draw For The Peterson LED Clearance/Side Marker/Third Brake Light PET75PV?
- Search Results: loom
- Search Results: 3 wire wiring
- Search Results: toggle switch
- Shop: Triplex Boat Cable with White Outer Jacket - 16 Gauge - Black-Green-White - per Foot
- Shop: Female Spade Terminal Quick-Disconnect - 16-14 Gauge - Fully-Insulated PVC - Qty 1
- Q&A: Basis for Weight Rating of Trailer Safety Chain
- Shop: Buyers Products 3/8" x 22" Class 4 Trailer Safety Chain w/ Clevis Hook - 30 Proof
- Shop: Uni-Lite LED Clearance and Side Marker Light w Grommet - Submersible - 2 Diodes - Clear Lens - Red
- Search Results: trailer tires and wheels
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: Measuring To Choose The Right Trailer Axle
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Search Results: trailer leaf springs
- Q&A: What Gauge Wire Should be Used to Wire Trailer Brakes
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Brake Controller
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
on Trailer Lights
