Replacement Landing Gear Legs for a Nu Wa Hitchhiker 5th Wheel Trailer
Published 05/23/2018
Products Featured in This Question
Question:
If my landing gear leg has stops that are welding in a different position than the ones I order is it possible for me to grind off the stop and weld in the position I need
asked by: Kenny
Expert Reply:
There are two measurements you will need to take in order to find the correct replacement landing gear legs for your Nu Wa Hitchhiker 5th wheel trailer. These measurements include the overall length of the leg's outer tube and the distance between the two weld stops.
There are two common outer tube measurements which are 29-1/2" long and 32-1/2" long. It sounds like you have 29-1/2" long therefore you can use part # LG-179013 for the lead leg and part # LG-179014 for the follow leg. However, in order to make sure these will be an exact fit for you, you will need to measure the distance between the weld stops on your existing landing gear legs. As long as they measure to be 15-1/2" inside to inside or 17-1/2" outside to outside (see photo) then these legs will work for you.
Product Page this Question was Asked From
Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Stromberg Carlson
more information >
Continue Researching
- Shop: Lippert Foot Pad for Standard 5th Wheel Landing Gear - 5" x 8"
- Shop: Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear
- Shop: Replacement Follow Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Q&A: Replacement Landing Gear for Frame Clamps That Measure 18-1/2 Inches Apart
- Video: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear Spec Review
- Video: Feature Review Replacement Follow Leg for Stromberg Carlson Landing Gear
- Video: Breaking Down the Replacement Follow Jack w/ Drop Leg for Stromberg Carlson Landing Gear
- Shop: Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
- Shop: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Shop: Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Q&A: Periodic Maintenance for Landing Gear Like # LG-179013 Without Grease Zerk
- Search Results: landing gear lead leg
- Q&A: Replacement Landing Gear Legs for a 2004 Keystone Cougar 254EFS
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Shop: Brake Controller
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
on Accessories and Parts
Kenny
5/23/2018
If my landing gear leg has stops that are welding in a different position than the ones I order is it possible for me to grind off the stop and weld in the position I need