Replacement Landing Gear for Frame Clamps That Measure 18-1/2 Inches Apart
Published 01/24/2019
Products Featured in This Question
Question:
Hi there. My spider gears on my landing gear need replaced on both the lead and follow Jacks. I dont want to replace the whole jack cause they are fine. My jacks have no info on them or anything. They are both the same size jack. Can I order some new gears even if the new ones are different than the old ones. I will be replacing both gears on each side. My RV is a 1999 Savvana
asked by: Cory B
Expert Reply:
If you have measured your landing gear like in the accompanying diagram and the frame clamps are 18-1/2 inches apart you have an uncommon spacing; you can use the Landing Gear Set # LG-183708 but would need to have a welder come in and remove your current brackets and weld new ones on that are the appropriate length.
The probable reason you have uncommon spacing between your brackets is the landing gear on your Avion Savannah was likely made by RBW some years ago and they are no longer in business which limits exact replacements for their parts.
Product Page this Question was Asked From
Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs
- Camper Jacks
- 5th Wheel Camper
- Landing Gear
- Steel
- 7001 - 8000 lbs
- Manual Jack
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: landing gear trailer jack
- Shop: Replacement Follow Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Shop: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Shop: Ultra-Fab Deluxe Electric Landing Gear Set - Weld On - 38" Lift - 12,000 lbs
- Search Results: landing gear crank handle
- Search Results: landing gear
- Video: Feature Review Replacement Follow Leg for Stromberg Carlson Landing Gear
- Search Results: trailer leaf springs
- Video: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear Spec Review
- Shop: Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear
- Shop: Lippert Foot Pad for Standard 5th Wheel Landing Gear - 5" x 8"
- Search Results: bronze bushings
- Search Results: rv steps
- Q&A: Replacement Landing Gear Legs for a Nu Wa Hitchhiker 5th Wheel Trailer
- Shop: Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
- Video: Breaking Down the Replacement Follow Jack w/ Drop Leg for Stromberg Carlson Landing Gear
- Q&A: Replacement Landing Gear with 29-1/2 Inch Legs
- Video: All You Need to Know About the Landing Gear Set
- Shop: 5-Leaf Double-Eye Spring for 6,000-lb Trailer Axles - 25-3/8" Long
- Video: In-Depth Review of the Landing Gear Set
- Video: Checking Out the Ultra-Fab Deluxe Electric Landing Gear Set
- Q&A: How to Choose the Correct Replacement Landing Gear for 5th Wheel Trailer
- Video: Detailed Breakdown of the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles
- Q&A: How to Manually Operate the Ultra-Fab Deluxe Electric Landing Gear Set
- Q&A: Periodic Maintenance for Landing Gear Like # LG-179013 Without Grease Zerk
- Search Results: rv waste valves
- Shop: Brake Controller
- Q&A: How to Measure for Replacement Landing Gear for 5th Wheel
- Q&A: How to Determine if Ultra-Fab Deluxe Electric Landing Gear Set Will Fit Trailer
Cory B.
1/16/2019
We were discussing my landing gear measurements, mine were the ones with the 18.5inch spacing and you asked if a 41inch cross shaft would work. The measurement between my two jacks is 80inch would the part number you gave me work?