Replacement Reverse Lockout Solenoid for Demco Hydraulic Brake Actuator DA10

Question

Question:

Will this work with Demco actuator DM 8104311?

asked by: Buzz H

0

Expert Reply:

Yes, the replacement Demco Solenoid Kit for Brake Actuators # DM5404 that you referenced is designed for Demco DA10 actuators like the Demco Hydraulic Brake Actuator # DM8104311 that you referenced.

expert reply by: Jameson C

0

Answer 1

Since the Titan Zinc-Plated Brake Actuator #T4750820 that you referenced has a weight capacity of 12,500 lbs and a tongue weight capacity of 1,250 lbs it will serve well as a replacement actuator for your application. The mounting holes are spaced…

view full answer...

Answer 2

Hey Jeff, welcome back. The Demco Hydraulic Brake Actuator w/ Electric Lockout item #DM62VR is going to work just fine to replace your 6,000 lbs one. The important part is making sure your trailer has disc brakes because you'll blow drums out…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Reverse Lockout Solenoid for Demco Hydraulic Brake Actuator DA10

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching