Instructions for Thule XADAPT9 Install on Thule Prologue

Question

Question:

I purchased a Thule Prologue and am trying to attach it to my aerobars with the xadapt9 but am not sure which slots the t-bolts should go through to connect the front of the Prologue to the bars. Thanks,

asked by: Jacob

0

Expert Reply:

I attached the install instructions for the Thule XADAPT9 part # THXADAPT9 that you referenced which I hope clears up the issue you are experiencing.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Thule Prologue Roof Mounted Bike Rack that you referenced will work with the Thule Aeroblade crossbars on your 2006 Jeep Grand Cherokee with the XADAPT9 load bar adapter, #THXADAPT9. This adapter comes with a curved metal bracket for the rear…

view full answer...

Answer 2

There is just one Thule Echelon bike rack, the Thule Echelon 518. As you mentioned, this is an older bike rack, but if you are sure this is what you have, then you can absolutely use the Thule Load Bar Adapter for Peloton and Echelon Bike Racks…

view full answer...

Answer 3

Hey Josh, yes the Thule Load Bar Adapter for Peloton and Echelon Bike Racks #THXADAPT9 does fit your Prologue bike rack and also will fit around your Thule Wingbar crossbars.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Instructions for Thule XADAPT9 Install on Thule Prologue

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching