Replacement Nylon Caps for Andersen Greaseless Hardball Hitch Balls

Question

Question:

will the replacement cap work on regular anderson hitch with 2 in and 2 5/16

asked by: William M

0

Expert Reply:

The 2 inch and 2-5/16 inch greaseless balls require different replacement caps. The 2-5/16 inch version is # AM3664-2516. The 2 inch is # AM3664-2. And the 1-7/8 inch is # AM3664-178.

expert reply by: Michael H

0

Answer 1

I went out to the warehouse and pulled greaseless ball to see how exactly the nylon cap is held on. It is not glued on or held on with a fastener. It is pressed on the ball. When it comes time to replace the cap, you would use some channel locks or…

view full answer...

Answer 2

Hi MH, The balls for the Rapid Hitch Adjustable, Locking, Aluminum Ball Mount Kit #AM3400 can rapidly be changed out by removing the bracket that holds the balls and then pulling out the locking pin #AM3440. With it removed you can slot in one of…

view full answer...

Answer 3

The part number you are looking for is the #AM3664-2 which is the replacement nylon cap for the Greaseless Hardball Hitch Ball in the 2 inch size.

view full answer...

Answer 4

Hi John; we do not have an installation video for the Replacement Converter Section for Progressive Dynamics Inteli-Power 4000 Series 45 Amp Power Center #PD4045CSV yet. The only thing I can offer at this time is the installation instructions from…

view full answer...

Answer 5

Thanks for the picture! The Replacement Converter Section item #PD4045CSV is the correct part you need to replace your PD4045KA converter. It is compatible with Lithium batteries you'll just have to flip the LI/LA switch. I linked the…

view full answer...

Answer 6

Hey Gary, The Replacement Converter Section #PD4045CSV can properly charge your LiFePO4 as long as you have the switch or black jumper (depending on the when yours was manufactured) in the "LI" position. If you're buying new it should…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Nylon Caps for Andersen Greaseless Hardball Hitch Balls

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching