Replacement Nylon Cap for 2 inch Greaseless HardBall Hitch Ball

Question

Question:

I’m searching for an Andersen Rapid hitch greaseless ball cap, previously I purchased these from you, now I can’t find the listing. I need 2 for a 2 inch ball. Thanks

asked by: Les L

0

Expert Reply:

The part number you are looking for is the # AM3664-2 which is the replacement nylon cap for the Greaseless Hardball Hitch Ball in the 2 inch size.

expert reply by: Jameson C

0

Answer 1

I went out to the warehouse and pulled greaseless ball to see how exactly the nylon cap is held on. It is not glued on or held on with a fastener. It is pressed on the ball. When it comes time to replace the cap, you would use some channel locks or…

view full answer...

Answer 2

The part you are looking for is the Replacement Nylon Cap for Greaseless HardBall Hitch Ball with 2" Diameter part #AM3664-2

view full answer...

Answer 3

For the MB Sturgis Sturgi-Stay T-Fitting w/ Hose for POL Valve - 2 Model 250 Quick Disconnect Ports #103538-MBS you will put this between the tank and the motorhome's in line regulator. Then you will need a single stage regulator like #CAM59013…

view full answer...

Answer 4

Hi MH, The balls for the Rapid Hitch Adjustable, Locking, Aluminum Ball Mount Kit #AM3400 can rapidly be changed out by removing the bracket that holds the balls and then pulling out the locking pin #AM3440. With it removed you can slot in one of…

view full answer...

Answer 5

Hi John; we do not have an installation video for the Replacement Converter Section for Progressive Dynamics Inteli-Power 4000 Series 45 Amp Power Center #PD4045CSV yet. The only thing I can offer at this time is the installation instructions from…

view full answer...

Answer 6

The 2 inch and 2-5/16 inch greaseless balls require different replacement caps. The 2-5/16 inch version is #AM3664-2516. The 2 inch is #AM3664-2. And the 1-7/8 inch is #AM3664-178.

view full answer...

Answer 7

Thanks for the picture! The Replacement Converter Section item #PD4045CSV is the correct part you need to replace your PD4045KA converter. It is compatible with Lithium batteries you'll just have to flip the LI/LA switch. I linked the…

view full answer...

Answer 8

Hey Gary, The Replacement Converter Section #PD4045CSV can properly charge your LiFePO4 as long as you have the switch or black jumper (depending on the when yours was manufactured) in the "LI" position. If you're buying new it should…

view full answer...

Answer 9

Yes, we two options, the GasStop RV Propane Emergency Shut-Off Safety Valve with a POL Connection, #GS84FR and the GasStop Propane Emergency Shut-Off Safety Valve with ACME Connection, #GS24FR. Which item you need is dependent on the connection you…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Nylon Cap for 2 inch Greaseless HardBall Hitch Ball

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching