How To Figure Out the Correct Replacement Hubs for EZ Loader Boat Trailer

Question

Question:

Hmm, ok. How about this...do you know what parts you have that match 300-031807 from ez loader?

asked by: David

0

Expert Reply:

In order to find the correct replacement hubs for your EZ Loader boat trailer you will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them. If you are unable to find them, you would need to use a digital caliper and measure your spindle to the thousandths of an inch where the bearings ride. You can use the photo I've attached to see exactly where you need to measure. From there you can match up the bearings with the appropriate replacement hub assembly.

I've also added a link to a help articles on wheel bearings as well as a link to our selection of hubs for you to take a look at.

expert reply by: Kyle S

0

click to enlarge

David

2/19/2018

Hmm, ok. How about this...do you know what parts you have that match 300-031807 from ez loader?

Kyle S.

2/19/2018

I was able to find an online parts list which detailed what you would need and we have everything you'd need but for the actual hub which you would need to get from EZ-Loader with part number 250-031438 because the idler hubs we carry with the correct bearings have a different grease seal than what you would need. The correct bearings for you are going to be inner bearing # L68149 and outer bearing # L44649. The accompanying races will be # L68111 and # L44610 while the correct grease seal is # 168255TB, which has a 1.687 inner diameter.

Answer 1

Linda, on the DC side, PowerMax power centers like the 45A #PM47VR, 55A #PM67VR, and 60A #PM77VR use standard automotive-style blade fuses, which are widely available and often reused from your existing setup, assuming fuses aren't blown. On the…

view full answer...

Answer 2

The Kodiak Disc Brake Kit #K2HR10A11RERR is actually specifically designed to fit an AL-KO 10k #99 spindle, so this will be a perfect replacement. Though this does include the oil cap, it should be noted that it does not include the bearings or seal.…

view full answer...

Answer 3

Hey, Jeff. Thanks for reaching out. Since your trailer has a 4 on 4 bolt pattern, there are two common bearing setups it could be using, so we’ll want to narrow that down. One option is a 1" straight spindle, which would use bearing #L44643 for…

view full answer...

Answer 4

For a 10k AL-KO trailer axle we have the Kodiak Disc Brake Kit part #K2HR10A11RERR but the #K2HR12A11-120DW that you referenced is designed for a 12k AL-KO axle.

view full answer...

Answer 5

For your 1996 EZ Loader trailer you will need to get the parts individually as we do not have a kit with all the correct parts. Inner Bearing #L68149 Inner Race #L68110 Outer Bearing #L44649 Outer Race #L44610 Grease Seal #168233 I recommend using…

view full answer...

Answer 6

Hello Chris, Thanks so much for writing in and a double thank you for including the full brake assembly part number. That is incredibly helpful! Since you have the Kodiak Disc Brake Kit 11.35" Rotor #120 Spindle 12K ALKO #K2HR12A11-120DW, you…

view full answer...

Answer 7

Hey, Harjot. It sounds like based off the measurements you got, your race most likely is part #L44610 which has a 1" inner diameter and goes on a straight spindle. The next step down from that is race part #LM11910 which is 0.75" diameter,…

view full answer...

Answer 8

Hey Charles, the Swagman E-Spec part #S45SR is rated for use at the rear of a travel trailer so it will work great for you. It is odd that it's not closer connected to the other RV rated bike racks but that's our fault and I'll see if I…

view full answer...

How To Figure Out the Correct Replacement Hubs for EZ Loader Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching