Bearing Replacement For a 1996 EZ Loader Boat Trailer

Question

Question:

What bearings kit for a 1996 ezloader trailer?

asked by: MICHAEL H

1

Helpful Expert Reply:

For your 1996 EZ Loader trailer you will need to get the parts individually as we do not have a kit with all the correct parts.

Inner Bearing # L68149
Inner Race # L68110
Outer Bearing # L44649
Outer Race # L44610
Grease Seal # 168233

I recommend using LubriMatic LMX Industrial Strength Grease # L11390 for the bearings. Its is highly water insoluble and able to withstand extreme pressures at hot and cold temperatures.

expert reply by: Bud M

1

Answer 1

The Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers #RM-2460-2570 will not include wet bolts. This is due to the system using slipper springs to replace the double eye springs that come on most trailers. With the slipper springs…

view full answer...

Answer 2

Hey Joseph, the CE Smith trailer hubs we offer that are pre-greased like the part #CE13515 come with the LMX Red grease like the #L11390.

view full answer...

Answer 3

I recommend using the LubriMatic LMX Industrial Strength Grease #L11390 on the Wet Bolts #LC52SV for the Road Armor Shock Absorbing Equalizer Kit #LC696740. This grease is formulated for superior performance in cold and hot climates. It is also…

view full answer...

Answer 4

Hey Viencent, thanks for the information! To replace the bushings in your slipper springs, I recommend the Dexter Bronze Bushings item #K71-291-00. These have a 11/16" outer diameter and will replace all four of the bushings on your car hauler.…

view full answer...

Answer 5

Hi Phil! The main difference between the etrailer Easy Grease Trailer Hub and Drum Assembly #AKHD-865-7-2-EZ-K and the Dexter Trailer Hub and Drum Assembly #42866UC3-EZ is where they are made. Ours are made over seas and Dexter hubs are made here in…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Bearing Replacement For a 1996 EZ Loader Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching