Do I Need To Remove Exhaust Heat Shields To Install CURT Trailer Hitch # 11352 On 2010 Nissan Altima
Published 05/13/2011
Products Featured in This Question
Question:
I dont want to lose the heat shields on my 2010 Nissan altima when I install a trailer hitch. Can the shields be modified and kept in placwe with this product??
asked by: Fred B
Expert Reply:
I do have some hitch options available for your 2010 Nissan Altima that do not require the removal of the heat shields, but the CURT trailer hitch # 11352, does require the heat shields to be removed.
The Draw-Tite hitch # 24796 will allow you to retain the heat shields on your 2010 Nissan Altima. It is a Class I 1-1/4 model, and is has the same tongue weight and towing capacity of the CURT hitch # 11352 that you selected.
To complete your towing setup, you will need the following items:
A ball mount
Tow Ready Wiring, part # 118470
1-7/8 inch hitch ball, part # 19256
2 inch hitch ball, part # 19258
If you will be using the hitch for a bike rack or other hitch accessories, you will be limited to those that are compatible with Class I hitches. You will want to make sure not to exceed the tongue weight and towing capacity of your hitch or vehicle as stated in the vehicle owners manual.
I have linked instructions and video installation of the Draw-Tite # 24796 and wiring # 118470 being installed on a 2010 Nissan Altima. I have also linked an FAQ on trailer hitch install tips.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: How to Install the Draw-Tite Sportframe Trailer Hitch Receiver on a 2017 Nissan Altima
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Mounting Bracket 4-Pole Flat
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: ShakeStopper Extreme Duty for Heavy-Hauler 5.3" RV Bumpers - 2" Hitch Receiver - 500 lbs
- Q&A: Removing Exhaust Heat Shield When Installing Curt Class I Hitch on 2013 Nissan Altima
- Q&A: Carrying Mobility Chair on Hitch Mount Carrier on 2017 Nissan Altima
- Q&A: Trailer Hitch and Bike Rack for 2013 Nissan Altima Sedan
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Instructions for Rampage Replacement Door Surrounds for Jeep # RA61098
- Q&A: Replacement Hardware For Draw-Tite Trailer Hitch For 2014 Nissan Maxima
- Q&A: Comparing Draw-Tite and Curt Trailer Hitches for a 2013 Nissan Altima Sedan
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How Much Weight Can I Put on My Trailer Hitch?
- Article: Rolling on a Budget: Top Wallet-Friendly Platform Bike Racks
- Article: Trailer Hitch Receiver Sizes
- Article: How to Measure for Trailer Hitch Drop
- Article: Ball Mount Basics: Weight Capacity, Class, and Size