Where Does Replacement Pintle Sleeve for Convert-A-Ball Pintle Hook Combos Item # PS Install

Question

Question:

Does this go over the hitch ball to snug up the slack when using a trailer with a pintle hitch?

asked by: Don S

0

Expert Reply:

The Replacement Pintle Sleeve for Convert-A-Ball Pintle Hook Combos Item # PS goes around the ball shaft on certain Convert-A-Ball pintle hook combo mounts such as # PH1. I have included a couple of pictures illustrating this for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

For the Convert-A-Ball Pintle Hook Combo with 3 Stainless Steel Balls #PH1 to fit with your 2-1/2 inch receiver, you will want a pintle mounting plate like the Titan Forged Pintle Hook Mounting Plate for 2-1/2" Trailer Hitches #RP45294 or the…

view full answer...

Answer 2

I do have an option for you but I don't recommend replacing the hitch ball on your pintle hook and ball combo. The reason for this is because unless you replaced the hitch ball with an exact replica then you run the risk of the hook disengaging…

view full answer...

Answer 3

Hey Bob, great question. It was about 7 degrees here in Missouri this morning, so I can relate to the cold. I do have a good solution for this too. What I would do is replace your current 7-way cord with the Curt Cold Weather 7-Way RV Style Connector…

view full answer...

Answer 4

The mounting holes on the Curt SecureLatch Pintle Hook #CU97FR are spaced 1-3/4" apart vertically and 3-3/8" horizontally on center. I have an alternate solution with the information you requested as when I spoke to Curt they said this…

view full answer...

Answer 5

My contact at Convert-A-Ball advises that their 10-Hole Cushioned Pintle Mounting Bar for 2-inch hitches, part #AMPC3, will provide you with your required 6 inches of drop. Their 8-hole version, part #AMPC2, will provide only 4 to 5 inches of drop.…

view full answer...

Answer 6

You would want to mount the Convert-A-Ball Pintle Hook Combo #PH1 to a mount such as #AMPC3 both of which use 1/2 inch bolts.

view full answer...

Answer 7

The center of the pin hole is 5-1/2 inches from the back of the mounting plate on the Cushioned Pintle Mounting Bar, part #AMPC3. The mounting plate itself is 1/2 inch thick. The support is 4 inches from the center of the hitch pin hole, and the…

view full answer...

Answer 8

I have a great solution for you. Take a look at the Convert-A-Ball Pintle Hook Combo with 3 Stainless Steel Balls #PH1. It comes with a pintle attachment and all 3 common ball sizes. The only other part needed is a shank such as #AMPC3, #AMPC2, or…

view full answer...

Answer 9

The Curt Pintle Hook with 2" Hitch Ball - Bolt On - 10,000 lbs/16,000 lbs #C48190 is not made in the USA but are made to US specs and requirements. Curt trailer hitch receivers are made in the USA, but not all of their products are domestically…

view full answer...

Answer 10

I checked with Curt who confirmed you can replace the 2 5/16 inch ball with a 2 inch ball #C48820 as needed with the Curt Pintle Hook with 2-5/16" Ball - 2-1/2" Hitches - 20,000 lbs #C45908. If you prefer the Convert-A-Ball option like you…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Where Does Replacement Pintle Sleeve for Convert-A-Ball Pintle Hook Combos Item # PS Install

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching