Recommended Pintle Hitch Made with USA Steel
Published 05/25/2018
Products Featured in This Question
Question:
Are these USA steel made is usa this is vip because i use holding up extremely heavy metal plates and I dont want to risk it falling off the tractor on to somebody
asked by: Kathy W
Helpful Expert Reply:
The Curt Pintle Hook with 2" Hitch Ball - Bolt On - 10,000 lbs/16,000 lbs # C48190 is not made in the USA but are made to US specs and requirements. Curt trailer hitch receivers are made in the USA, but not all of their products are domestically manufactured.
The only USA made pintle hook with ball we carry is the Convert-A-Ball Pintle Hook Combo with 3 Stainless Steel Balls - Bolt On - 25,000 lbs # PH1. The mounting holes are 3-3/8 inches apart horizontally center to center. Top to bottom they are 1-3/4 inches apart center to center.
Product Page this Question was Asked From
Curt Pintle Hook with 2" Hitch Ball - Bolt On - 10,000 lbs/16,000 lbs
- Pintle Hitch
- Pintle Hook - Ball Combo
- Adjustable Height
- 16000 lbs GTW
- Bumper Mount
- Plate Mount
- 2 Inch Ball
- No Shank
- CURT
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Convert-A-Ball Pintle Hook Combo with 3 Stainless Steel Balls - Bolt On - 25,000 lbs
- Shop: Curt Pintle Hook Mounting Plate for 2-1/2" Hitches - 10-3/4" Shank - 8 Hole - 20,000 lbs
- Shop: Convert-A-Ball Shank - 1" Diameter - 2-1/4" Long - Stainless Steel - 10,000 lbs
- Shop: Curt Cold Weather 7-Way RV Style Connector - Trailer End - 10' Long - RV Standard
- Search Results: convertaball
- Search Results: convert a ball shank
- Shop: B&W Ball for Gooseneck Flat Plate Hitch - 2-5/16" Ball - 4" Long Shank - 30K
- Shop: Convert-A-Ball Shank - 3/4" Diameter - 2-1/4" Long - Stainless Steel - 5,000 lbs
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Q&A: Thread Pitch on Hitch Balls that Have 1 inch Diameter Shank
- Search Results: trailer wiring
- Search Results: 118158
- Search Results: 11604
- Search Results: pk11604
- Search Results: plate mount
- Q&A: Recommended Pintle Hook Mounting Plate for 2-1/2 Inch Trailer Hitch Receiver
- Q&A: Solution For 7-Way Cord That Becomes Rigin In The Cold Weather
- Q&A: Mounting Hole Locations And Plate Thickness Required For Combination Pintle Hook 2-5/16 Ball Combo
- Q&A: Can the Hitch Ball On a Pintle Hook and Ball Combo Be Replaced
- Q&A: Convert-a-Ball Cushioned Pintle Mounting Bar Measurements
- Q&A: Is there a Convert a Ball Hitch with Pintle Hook and 2 inch ball Capabilities Available?
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Shop: Brake Controller
on Pintle Hitch
