Replacement Support Pegs for RV Exterior Ladder

Question

Question:

Can I buy just the 4 suports for my ladder? I dont need anything else. My up righys are staright.

asked by: Jack M

0

Expert Reply:

We do have replacement support pegs available for RV exterior ladders, which I have linked for you to look through.

In order to choose a compatible replacement, you will want to measure the length of your existing units. For 5 inch support pegs, we have # SPN-416 or # 8535. We also have 12 inch pegs with # SC8531, which includes the hardware as well.

expert reply by: Chris R

0

Answer 1

The Replacement Ladder Support Peg for Stromberg Carlson RV Exterior Ladder - Round Base - 12" #SC8531 is the aluminum support with 2-1/8 inch round base. We don't have them in the 5 inch length, but you can trim the 12 inch ones to desired…

view full answer...

Answer 2

We have some that are 12 inches long, #SC8531, but none that are 8 inches. You could trim the 12 inch ones though as long as you make a straight cut to put the end cap back on.

view full answer...

Answer 3

We do offer a range of RV exterior ladders that are general-purpose replacements that will work on many trailers and RVs, but none of these is a custom-fit item intended as an exact OEM replacement for any particular unit. RV makers may change ladder…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Replacement Support Pegs for RV Exterior Ladder

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching