How to Pick Out Ball Mount for Trailer Hitch

Question

Question:

Not sure what its called but its part of of the hitch. It is L shaped and slides in the receiver hitch. Need one soon!

asked by: m

0

Expert Reply:

Is it possible you are looking for a ball mount like the part # C45036. The ball mount platform is somewhat L-shaped.

I attached an article that details how to pick out a ball mount that will allow your trailer to be towed level.

expert reply by: Jameson C

0

Answer 1

You are on the right track! The Draw Tite hitch part #75528 is a confirmed fit for your 2014 Buick Enclave as well as the trailer wiring kit #118270. The wiring mount part #18144 will also give you a place to mount the 4-way that bolts to the bumper.…

view full answer...

Answer 2

The closest you can get to level is preferred. The Curt Ball Mount #C45036 is likely going to be the closest you'll find and will work for you as long as your trailer's coupler fits a 2 inch hitch ball. If you need a 2-5/16 inch ball,…

view full answer...

Answer 3

The Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K #2753 is not the correct fit for zero rise or drop. For the zero rise or drop you will need the Curt Solid 2-Ball Mount for 2" Hitches - 2"…

view full answer...

Answer 4

The Malone #MPG550-U MegaSport Kayak trailer has crossbars that are 86 inches long. If you place your two larger kayaks in the saddles, and the saddles are adjusted to the kayaks sit right up against each other, you'll still have 22 inches of…

view full answer...

Answer 5

I believe I have found the replacement wheel you are looking for. It's kind of hard to see in our product pictures but the Dexstar Steel Mini Mod Wheel part #AM20443 has a sticker on it that reads 17-231 and is a 15 inch diameter wheel with a 5…

view full answer...

Answer 6

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Blaise, with the Curt hitch #C35MJ installed on your 2025 Crown Signia it doesn't have a 4-way bracket built in like you noticed but the Curt kit part #C59236 would actually get stored in the rear cargo area of your vehicle when not in use so…

view full answer...

Answer 9

If you look at your rear leaf springs, and see an extra leaf as shown in the diagram, you have the overload spring option. For a 1997 F350 with overload springs, you'd need the B and W Turnover Ball #BWGNRK1110. If your truck does NOT have the…

view full answer...

Answer 10

I attached a chart that has the automotive cross reference for the Kodiak disc brake pads part #K2250CP that you referenced under the yellow heading. Probably the easiest to look up would be 1982 to 1992 Chevy Cavalier.

view full answer...

Answer 11

Hey Pete, thanks for the picture of your current tire. From seeing that I can tell it has a Load Range of C. The Kenda ST235/75R15 Radial Off-Road Trailer Tire #KE68JR that you referenced is actually a Load Range D which means it has a weight…

view full answer...

How to Pick Out Ball Mount for Trailer Hitch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching