Recommended Ball Mount with to Tow a Trailer Level that Needs 1 Inch of Drop
Updated 08/29/2017 | Published 08/28/2017 >
Products Featured in This Question
Question:
I have a 2009 Cad Escalade, rated to pull 7800 lbs.I have a Venture Alum boat trailer with a 7000 total weight boat to pull. I have a class III hitch. There is a sticker on the trailer which recommends a hitch height of 22. The top of my receiver hole is 23. Is the Curt Class III 7500GVW mount and ball my best bet?
asked by: Mark W
Expert Reply:
The closest you can get to level is preferred. The Curt Ball Mount # C45036 is likely going to be the closest you'll find and will work for you as long as your trailer's coupler fits a 2 inch hitch ball. If you need a 2-5/16 inch ball, instead, use # C45041.
Instead of going by the recommendation on the trailer's sticker you might take a measurement. With the trailer on level ground measure from the ground to the bottom of the coupler. The difference between this number and the 23 inches of your Escalade's receiver tube is the rise or drop you need.
Product Page this Question was Asked From
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- One Ball
- 2 Inch Ball
- Steel Shank
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- CURT
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Search Results: butt connectors wiring
- Video: Curt Class III Ball Mount with 2" Ball Spec Review
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2023 Ford Bronco Sport
- Q&A: 2 Inch Ball Mount with Zero Rise or Drop for Level Towing
- Q&A: How to Pick Out Ball Mount for Trailer Hitch
- Q&A: How to Select Correct Ball Mount to Keep Pop-Up Camper Trailer Level When Hitched
- Q&A: Trailer Towing Setup Recommendation for 2014 Buick Enclave
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer hitch ball mount
- Search Results: trailer wiring
- Search Results: rubber hitch covers
- Shop: TowSmart Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 5K
- Shop: Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Rubber Tube Cover for 2" Trailer Hitch Receivers
- Q&A: Will Three Kayaks Fit on the Malone MPG550-U MegaSport Trailer
- Search Results: edge guard
- Search Results: u~channel edge trim trailer door parts
- Shop: D-Shaped Rubber Seal for Enclosed Trailer - Stick On - 25' Long x 3/4" Wide
- Search Results: towsmart trailer hitch
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Suspension Enhancement




