What Grade of Hardware Comes with 10k Hitch for 1977 Ford F-250 C14082

Question

Question:

I,have a 1977 f 250 camper special 2 wheel drive .I m looking for an 8000 lb. receiver. Does it come with grade 5 bolts ???

asked by: Steve F

0

Expert Reply:

For a hitch that has a 10k capacity that fits your 1977 Ford F-250 you would want the Curt hitch part # C14082.

The hardware that comes with this is Grade 5.

expert reply by: Jameson C

0

Answer 1

The Curt Trailer Hitch Receiver part #13028 could potentially fit your 1966 Chevrolet C10 with aftermarket bumper. However, I would not be able to confirm this as the trailer hitch is only tested with the OEM bumper. I have attached a photo for you…

view full answer...

Answer 2

The measurement from the top of the mounting bracket down to the top of the receiver tube measures 5 inches. Curt trailer hitch #C14082 is a custom fit hitch designed to fit the following vehicles: 1973 - 2000 Chevrolet C/K Series Pickup Cab and…

view full answer...

Answer 3

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 4

As we have not had a 1973 Ford F-100 in our shop to test fit the available receivers I can only give you the measurements from one of our receivers so that you can see where it will sit on your truck. The Curt Trailer Hitch Receiver #C14082 is…

view full answer...

Answer 5

Actually several of your pictures did make it through! What you have there is the standard/step bumper on your 1979 Chevy C-10. Deep drop bumpers, also called cowboy bumpers, drop way down. If your truck has an 8 foot bed you can use Curt trailer…

view full answer...

Answer 6

Buyers Products Class V hitch #3371801102 fits the cutaway cab and chassis version of the 2003 GMC Savana Van. For the cargo and passenger van version their Class V hitch #3371801100 is the correct fit. I am not sure which version of the base vehicle…

view full answer...

Answer 7

We don't have any hitches that are confirmed to fit on the CUCV M1008 military truck, but from what I was able to find out is that it's a version of the Chevy C/K series trucks that were manufactured for civilian use. You may be able to use…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

What Grade of Hardware Comes with 10k Hitch for 1977 Ford F-250 C14082

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching