Hardware Needed to Install Timbren Spacer with Suspension Enhancement System on 2013 Ram 1500

Question

Question:

I want to add the 1 inch spacer to my dr1500dq kit. How long of bolt do i need to purchase? Is there any special grade of bolt i need to look for? Looking forward to hearing back from you. Thanks.

asked by: Brian

0

Expert Reply:

To install the Timbren Spacer # A25723-90AH00 you need an M10-1.5 Hex Cap Screw that's Grade 8.8 and 75 mm long according to Timbren.

It should be a zinc bolt to resist corrosion and since the # TDR1500DQ normally comes fully assembled use some Loctite Threadlocker # LT37420 as well.

expert reply by: Charles S

0

Answer 1

Hey good question, Adam. There is not a specific limit on how many spacers you can use with Timbrens. Most trucks that use Timbrens would not be lifted more than 4"-6" anyway, and I have heard of people using up to 6 spacers on each side. I…

view full answer...

Answer 2

Hey Thomas. I wouldn't say ones better than the other and they have identical installation processes as far as removing the shock tower assembly. It has to come off for both on your truck. The main differences between the Timbren item #TFF350SD4…

view full answer...

Answer 3

Thanks for your question, Steve. Installing the Timbren Rear Suspension Enhancement System #T76FR wouldn’t eliminate the need for a weight distribution system if your setup calls for one, they actually serve two different purposes. A weight…

view full answer...

Answer 4

That's a cool set up you have there, and the best option for suspension enhancement for your 2022 Toyota Tundra is going to be Timbrens to help support the added weight in the rear. The correct part number for your '22 Tundra is the…

view full answer...

Answer 5

You would want to go with the Timbren kit that fits your 2020 Ram 1500 part #TDR1500DS and then since you have a 6 inch lift you'd need a quantity of 12 of the Timbren 1 inch spacers #A25723-90AH00 to take up the extra space.

view full answer...

Answer 6

Hey Kirk, for the SumoSprings kit part #SS46PV that fits your 2024 Toyota Tundra you'd need to use the Timbren spacer blocks part #A25723-90AH00 to take up that extra space created by the lift. You'd need 4 of these per side as these are 1…

view full answer...

Answer 7

Hey Matthew, yes the Timbren kit part #TTORSEQ1 that you referenced would work great on a vehicle that is lifted but you have to use spacers to take up that extra space created like with the part #T68MR. How big of a lift does your vehicle have?

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Hardware Needed to Install Timbren Spacer with Suspension Enhancement System on 2013 Ram 1500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching