Timbren Suspension Solution for 2020 Ram 1500 with 6 inch Lift

Question

Question:

I have a 2020 Ram 1500 Rebel Sport with a 6’ lift, which products would help most to eliminate the squat when pulling my sideXside? Thanks

asked by: Bobby P

0

Expert Reply:

You would want to go with the Timbren kit that fits your 2020 Ram 1500 part # TDR1500DS and then since you have a 6 inch lift you'd need a quantity of 12 of the Timbren 1 inch spacers # A25723-90AH00 to take up the extra space.

expert reply by: Jameson C

0

Answer 1

Hi Chris; it looks like you already picked up the Timbren SES #TDR1500DQ along with the Spacer Kit #T68MR. The Timbren itself is 5-1/2" tall so 3" worth of spacers would do the trick if you follow the recommended 1" gap or 3-1/2"…

view full answer...

Answer 2

Hey good question, Adam. There is not a specific limit on how many spacers you can use with Timbrens. Most trucks that use Timbrens would not be lifted more than 4"-6" anyway, and I have heard of people using up to 6 spacers on each side. I…

view full answer...

Answer 3

Hey Matthew, yes the Timbren kit part #TTORSEQ1 that you referenced would work great on a vehicle that is lifted but you have to use spacers to take up that extra space created like with the part #T68MR. How big of a lift does your vehicle have?

view full answer...

Answer 4

I checked with Timbren and the bolts that come with the Timbren part #TGMFK25S that you referenced are M10x1.5X30.

view full answer...

Answer 5

Hey Brian, the correct Timbren kit for a 2023 Ram 1500 4x4 is the part #TDR1500DS.

view full answer...

Answer 6

Hey Dave, with Timbrens like the part #TFR1504E you want there to be a gap of right at 1 inch between where the spring contacts the bracket so that you get a decent ride quality plus the support you want. If you add a spacer to make it contact sooner…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Timbren Suspension Solution for 2020 Ram 1500 with 6 inch Lift

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching