Picture of Finished Installation of Westin MAX Winch Mounting Tray 46-21245

Question

Question:

Was wondering if you have any pictures of this installed on the vehicle? Does it mount with /behind the factory bumper ? I have a 06 gmc 2500hd.

asked by: Don

0

Expert Reply:

Westin MAX Winch Mounting Tray # 46-21245 is a confirmed fit for your 2006 GMC Sierra 2500 HD and it mounts in front of the factory bumper. The linked photo, taken from the install instructions which I've sent to you, shows the finished appearance (along with a bull bar).

expert reply by: Adam R

0

click to enlarge

Answer 1

The Center Section #C-52 for the Curt Overbed, Folding Ball Gooseneck Trailer Hitch #C61341-52 is very close to the measurements you provided. I have included an image with the measurements for this as the front to back mounting holes are 9-3/4"…

view full answer...

Answer 2

Since gooseneck and 5th wheel hitch brackets need to match with the hitches themselves, even if your Atwood folding gooseneck hitch fit the Curt rails I couldn't recommend doing so because they have never been tested together. For a similar…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

The correct replacement airbag for your Air Lift LoadLifter 5000 part 5813 is the Replacement Air Spring for Air Lift LoadLifter 5000 part #AL50201.

view full answer...

Answer 9

Hi Randy; that part number corresponds with the OEM Chill Cube. At this time, there are no heat strips available from Furrion. They have said they are developing one, but it has been over a year with no word on an ETA. The only option for heat on a…

view full answer...

Answer 10

Since winches draw quite a bit of amperage you'll need a winch wiring kit that uses heavy gauge wires to keep your trailer battery charged. On the trailer side you'd want the 7-1/2 foot long wiring kit part #BDW20347 which uses 1 gauge wire…

view full answer...

Answer 11

In regards to the Curt Trailer Hitch Receiver part #C15302 which is a fit for a 2001 Chevrolet Silverado 2500 HD - 6-1/2 Foot Bed, there are only two factory weld nuts in the frame which get reused, they are the two closest to the bumper. The other…

view full answer...

Picture of Finished Installation of Westin MAX Winch Mounting Tray 46-21245

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching