Strap Recommendation for Dutton Lainson Boat Winch #14627

Question

Question:

I have a 2,500 pound boat. What winch strap should I order when I purchase boat winch #14627 from you?

asked by: Brian B

0

Expert Reply:

For a strap to use with the Dutton Lainson winch part # DL14627 the part # DL24249 would be an excellent option. This is a 25 foot long strap that has a 4k capacity.

I attached a review video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Hey Dave, I think you figured out your problem without realizing it - you need to have either lock washers or nylon lock nut in order to secure the CE Smith Bolster and Swivel Bracket Assemblies #CE10000G-4 to your trailer frame. Without hardware…

view full answer...

Answer 2

If the gear is broken on your existing Shelby winch, I recommend simply replacing the entire unit, as Shelby is no longer in business and replacement parts are not readily available. To replace your Shelby 5408 model, I recommend the Dutton-Lainson…

view full answer...

Answer 3

The bottom plate for the Dutton-Lainson Hand Winch #DL14627 is 4-3/4" wide x 5-1/2" long, while the bottom plate of the #DL14725 is slightly larger at 4-3/4" wide x 6-5/8" long. The diameter of the spools are exactly the same at…

view full answer...

Answer 4

Yep, it sure does; the 20 foot strap is indeed included with the 2-Speed Boat Trailer Winch #315-W2000D.

view full answer...

Answer 5

Shelby is no longer in business and would not be the same as Fulton; there are no ratchet repair kits available for Shelby so you'll need to replace your winch. Keeping in mind that a boat trailer winch has a boat-size-to-winch capacity that is…

view full answer...

Answer 6

I've attached the bolt pattern measurements for you of the Fulton High-Performance 2-Speed Trailer Winch #F142412. The only thing I wasn't able to fit on the diagram is the length of the slots. The top two slots are 1 inch long and the longer…

view full answer...

Answer 7

I've attached two pictures of the bolt pattern of the Fulton Winch #F142401. One shows the size of each bolt hole and the other shows the distance between the holes.

view full answer...

Answer 8

The Fulton XLT Swivel Trailer Jack #F141133 that you referenced comes ready to be installed and used. It would not require any greasing prior to initial use.

view full answer...

Answer 9

From what I have found, the Dutton-Lainson Hand Winch - TUFFPLATE Finish - Single Speed - 1,800 lbs #DL14627 will match the bolt pattern of your Shelby 5407B. I have attached a diagram as well as the dimensional drawing showing the bolt pattern on…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Strap Recommendation for Dutton Lainson Boat Winch #14627

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching