Do the Fulton XLT Jacks Require Grease Upon Install

Question

Question:

Is it necessary to lube/grease the Fulton Trailer Jack Code: F141133 XLT after installing and before actual usage? Thanks,

asked by: Vince G

0

Expert Reply:

The Fulton XLT Swivel Trailer Jack # F141133 that you referenced comes ready to be installed and used. It would not require any greasing prior to initial use.

expert reply by: Jameson C

0

Answer 1

Thank you for the photo of your Fulton jack. Your jack is a bolt-thru type pull-pin swivel jack. The 1500-lb-rated Fulton jack you can use in place of your existing one is part #FXP15L.

view full answer...

Answer 2

Hey Dave, I think you figured out your problem without realizing it - you need to have either lock washers or nylon lock nut in order to secure the CE Smith Bolster and Swivel Bracket Assemblies #CE10000G-4 to your trailer frame. Without hardware…

view full answer...

Answer 3

For a strap to use with the Dutton Lainson winch part #DL14627 the part #DL24249 would be an excellent option. This is a 25 foot long strap that has a 4k capacity. I attached a review video for you to check out as well.

view full answer...

Answer 4

The bottom plate for the Dutton-Lainson Hand Winch #DL14627 is 4-3/4" wide x 5-1/2" long, while the bottom plate of the #DL14725 is slightly larger at 4-3/4" wide x 6-5/8" long. The diameter of the spools are exactly the same at…

view full answer...

Answer 5

Shelby is no longer in business and would not be the same as Fulton; there are no ratchet repair kits available for Shelby so you'll need to replace your winch. Keeping in mind that a boat trailer winch has a boat-size-to-winch capacity that is…

view full answer...

Answer 6

If the gear is broken on your existing Shelby winch, I recommend simply replacing the entire unit, as Shelby is no longer in business and replacement parts are not readily available. To replace your Shelby 5408 model, I recommend the Dutton-Lainson…

view full answer...

Answer 7

Yep, it sure does; the 20 foot strap is indeed included with the 2-Speed Boat Trailer Winch #315-W2000D.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Do the Fulton XLT Jacks Require Grease Upon Install

Featured Help Information

Miscellaneous Media

Continue Researching