Bolt Hole Pattern of Fulton High-Performance 2-Speed Winch # F142412

Question

Question:

What are the size of the mounting holes and distances apart? I need to mount this to my 2inch square trailer neck to pull heavy loads up a 6foot ramp into my utility trailer. Thanks

asked by: Richard P

1

Helpful Expert Reply:

I've attached the bolt pattern measurements for you of the Fulton High-Performance 2-Speed Trailer Winch # F142412. The only thing I wasn't able to fit on the diagram is the length of the slots. The top two slots are 1 inch long and the longer slot is 2-1/4 inches long. Let me know if you have further questions.

For the strap, you can use the Fulton Heavy-Duty Winch Strap with Hook - 20' x 2" - 10,000 lbs # FWS20HD0200.

expert reply by: Jason S

1

click to enlarge

Answer 1

I went out to our warehouse so I could take some measurements on the Dutton-Lainson Hand Winch #DL14825 that you referenced. The main body of the winch measures 7 inches long, 5 inches tall, and 4-7/8 inches wide. With the wheel its length is 9-1/2…

view full answer...

Answer 2

Hey Dave, I think you figured out your problem without realizing it - you need to have either lock washers or nylon lock nut in order to secure the CE Smith Bolster and Swivel Bracket Assemblies #CE10000G-4 to your trailer frame. Without hardware…

view full answer...

Answer 3

For a strap to use with the Dutton Lainson winch part #DL14627 the part #DL24249 would be an excellent option. This is a 25 foot long strap that has a 4k capacity. I attached a review video for you to check out as well.

view full answer...

Answer 4

I've attached two pictures of the bolt pattern of the Fulton Winch #F142401. One shows the size of each bolt hole and the other shows the distance between the holes.

view full answer...

Answer 5

From what I have found, the Dutton-Lainson Hand Winch - TUFFPLATE Finish - Single Speed - 1,800 lbs #DL14627 will match the bolt pattern of your Shelby 5407B. I have attached a diagram as well as the dimensional drawing showing the bolt pattern on…

view full answer...

Answer 6

The 1,800-lb Fulton winch #F142306 we offer does come with a strap included. The strap is a 20-ft long polyester strap. The winch also has a 10-inch handle.

view full answer...

Answer 7

Yes, since the Dutton Lainson #DL14627 has a higher ratio of 5.4:1 and also has a slightly longer winch handle than the Fulton #F142306 it would be easier to turn. It would be a noticeable difference.

view full answer...

Answer 8

I went out to the warehouse to measure the distance between the mounting holes on the Fulton Fulton Single Speed Trailer Winch #F142306 and found the distance between the center hole and left hole to be 3/8". The holes on the Fulton are…

view full answer...

Answer 9

I went out to our warehouse to take some measurements of the mounting base on the Fulton Single Speed Trailer Winch #F142306. The plate itself measures 6 inches long and 4 inches wide. The mounting pattern features a few oblong holes that allows it…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Bolt Hole Pattern of Fulton High-Performance 2-Speed Winch # F142412

Featured Help Information

Miscellaneous Media

Continue Researching