Mounting Hole Spacing for Fulton Winch # F142401

Question

Question:

I need to know what the bolt spacing measurements are. I want to make sure it fits the plate on my trailer before I order it. Thanks

asked by: Rick W

0

Expert Reply:

I've attached two pictures of the bolt pattern of the Fulton Winch # F142401. One shows the size of each bolt hole and the other shows the distance between the holes.

expert reply by: Charles S

0

click to enlarge

Answer 1

The closest option we have to replace your Shelby industries hand winch model 54073, is the 2-Speed Boat Trailer Winch item #315-W2000D you were looking at. This 2-speed, manual ratcheting winch has a 2,000 lbs capacity. It includes a 20' long x…

view full answer...

Answer 2

I went out to our warehouse and measured the Single-Speed Boat Trailer Winch part #315-W2000D for you. The dimensions of the base are as follows; 6-1/4" long x 3-3/4" wide.

view full answer...

Answer 3

The bolt hole dimensions on the bottom of the Jif Marine Single-Speed Boat Trailer Winch with 20' Strap and Brake item #315-W2000D are 2.5 inches apart center to center. The attachment point to the center bolt is a slot that is 3.5 inches - 5…

view full answer...

Answer 4

The driver's side lamp, part #432400 has an additional function that the #432200 passenger side lamp does not. The driver's side features a clear lens on the underside of the lamp housing that would illuminate a license plate mounted…

view full answer...

Answer 5

For a strap to use with the Dutton Lainson winch part #DL14627 the part #DL24249 would be an excellent option. This is a 25 foot long strap that has a 4k capacity. I attached a review video for you to check out as well.

view full answer...

Answer 6

Hey Dave, I think you figured out your problem without realizing it - you need to have either lock washers or nylon lock nut in order to secure the CE Smith Bolster and Swivel Bracket Assemblies #CE10000G-4 to your trailer frame. Without hardware…

view full answer...

Answer 7

I've attached the bolt pattern measurements for you of the Fulton High-Performance 2-Speed Trailer Winch #F142412. The only thing I wasn't able to fit on the diagram is the length of the slots. The top two slots are 1 inch long and the longer…

view full answer...

Answer 8

From what I have found, the Dutton-Lainson Hand Winch - TUFFPLATE Finish - Single Speed - 1,800 lbs #DL14627 will match the bolt pattern of your Shelby 5407B. I have attached a diagram as well as the dimensional drawing showing the bolt pattern on…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Mounting Hole Spacing for Fulton Winch # F142401

Continue Researching