See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Recommended Hitch for a 2023 Toyota Corolla Hybrid Sedan
  For your 2023 Toyota Corolla Hybrid Sedan, I recommend the Curt Trailer Hitch item # C34UR. This hitch is custom fit and bolts to your Corolla with included hardware. This is a class I hitch with a 1-1/4" receiver. It has a 2,000 lbs towing capacity and a 200 lbs maximum tongue weight. This is the highest capacity hitch available for your car. I have linked an installation video below along with a picture so you can see what this hitch looks like installed. If you are planning on towing...
  view full answer...
  
• Can I Tow My Geo Pro 15TB Travel Trailer With My 2018 Volvo XC60
  I can get you setup to tow your travel trailer with your 2018 Volvo XC60. The answer to your first question is no, you cannot use a hitch receiver adapter to tow. I did check your owner's manual and your vehicle is rated to tow up to 3,500 lbs with a brake controller. (3,280 lbs if you will be towing 1,000m or higher, above sea level.) As a result, you should not have any problems towing the Geo Pro 15TB travel trailer. In order to tow your travel trailer you will need a hitch and a ball...
  view full answer...
• Trailer Hitch Fit for a 2020 Toyota Corolla
  We actually do have a trailer hitch for your 2020 Toyota Corolla Sedan! It is the Class I Draw-Tite Sportframe Trailer Hitch Receiver # 24983 and it has a 1-1/4" hitch receiver. You did refer to this as a tow hitch so if you planned on using this trailer hitch for towing you also need some wiring and a ball mount kit. I recommend the Tekonsha T-One # 118810 for wiring because of how reliable it is and that it bypasses your OEM wiring so you know your vehicle is protected. For a ball mount...
  view full answer...
• Correct Towing Capacity of Curt Hitch for 2004 Pontiac Vibe
  The correct capacity for Curt hitch # C12234 is 2000 lbs towing and 200 lbs tongue weight. I took a look at the owner's manual and it states that your 2004 Pontiac Vibe has a maximum towing capacity of 1,500 lbs, which is the weight you would need to go by. That hitch does come with a drawbar and pin and clip, though if you are looking to tow you will also need a 4-flat connector, which you can add with T-One Vehicle Wiring Harness # 118458. For a 1-7/8" hitch ball you would need # A-80...
  view full answer...
• What is the Best Hitch for a 2013 Hyundai Sonata Hybrid?
  The best hitch for your 2013 Hyundai Sonata Hybrid is going to be the Draw-Tite item # 24965. This hitch is custom fit for the hybrid models and bolts to your car with included hardware. It is the strongest and safest hitch available for your Sonata. I have linked an installation video below to help you get it set up. Since you are planning on towing you will also need a wiring harness item # C59236 and the Draw-Tite Drawbar item # 3593 and then for hitch balls item # 19258 for a 2...
  view full answer...
• Trailer Hitch, Wiring Harness and Ball Mount Recommendation for 2018 Toyota Corolla
  I took a look at an online copy of the owner's manual for a 2018 Toyota Corolla and it simply states that towing a trailer is not recommended with the vehicle so the decision will ultimately be up to you. If you do decide to use your '18 Corolla to pull your jet ski you will need a trailer hitch, wiring harness, ball mount and hitch ball. The trailer hitch I highly recommend for your '18 Corolla is the Draw-Tite Trailer Hitch # 24913 because it is a bolt-on installation that will not require...
  view full answer...
  
• What is the Best Wiring Harness for a 2018 Toyota Corolla iM?
  The best plug and play wiring harness for a 2018 Toyota Corolla iM is the Curt item # C56309. Curt makes some of the best and most reliable wiring harnesses in the towing business. Multiple manufactures use them as suppliers of their OEM towing harnesses. The Curt item # C56309 has a custom-fit T-connector that plugs into your Corolla's wiring harness, which is located behind the tail lights. It will provide you with a 4-flat connector that will power your trailer or accessories lighting...
  view full answer...
• Recommended Hitch for a 2024 Honda Accord
  To add a hitch to your 2024 Honda Accord, I recommend the Draw-Tite item # DT86PR. This hitch is custom fit and bolts to your Honda with included hardware. It is a class I hitch with a 1-1/4" receiver that has a 2,000 lbs towing capacity and a 200 lbs maximum tongue weight. If you are planning on towing you will also need a wiring harness item # 118776 and the Draw-Tite Drawbar item # 3593 and then for hitch balls item # 19258 for a 2 inch ball or item # 19256 for a 1-7/8 inch ball.
  view full answer...
• Hitch for 2020 Volkswagen Golf for Towing Small Motorcycle Trailer
  For lighter duty vehicles like your 2020 Volkswagen Golf a 1-1/4 inch hitch like the Curt part # C11412 would be your best option for towing a smaller trailer. You'll also need trailer wiring like part # 118646, ball mount # 3593, and hitch ball # 19256. If you have a GTI model, the Stealth Hitch # SH79ZR is a 2" but you cannot use to tow, the EcoHitch Stealth Trailer Hitch Receiver is also a 2" # 306-X7375 that is confirmed to fit the GTI. If you do not have the GTI model, then there...
  view full answer...
• Are Class II Hitches Available for a 2007 Toyota Corolla?
  Each hitch that is available for a 2007 Toyota Corolla is a Class I hitch with a 1-1/4" receiver such as the Draw-Tite # 24913. According to the '07 Corolla's owners manual, the towing capacity of the vehicle is 1,500 lbs, which is why there are no Class II hitches available. The Class I Draw-Tite has a 2,000 lbs towing capacity and 200 lbs tongue weight capacity, and if you were looking to tow, you would need to add a 4-flat connector # 55542 as well as drawbar # 3593, which comes with...
  view full answer...
• Trailer Hitch and Wiring Recommendation for 2017 Toyota Prius V
  For a trailer hitch for your 2017 Toyota Prius V the best choice is the Draw Tite part # 24847 as it is custom fit for your vehicle and has a great price. For trailer wiring you would want the part # 118610. For a ball mount you would want the part # 3593 which is designed for the hitch and then for a 2 inch hitch ball you would want the part # 19258.
  view full answer...
• Trailer Hitch Installation On 2015 Mitsubishi Lancer GT
  The Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 24885 is a confirmed fit for your 2015 Mitsubishi Lancer GT as long as you don't have the dual exhaust. There is no drilling required to install this hitch. The installation instructions state you will need a jig saw, cut-off wheel, or die grinder for enlarging the hole already present in the frame for the carriage bolt and block on the passenger side. I've attached the installation details which state...
  view full answer...
• Best Way to Transport Heavy SUP & Kayaks on 2014 Kia Soul That has Factory Roof Rack
  So there is a way that is going to allow you to transport your kayaks and SUP with your 2014 Kia Soul, but the issue is the factory roof rack, so the only option is going to be a kayak trailer. There simply isn't any type of load assist that is going to work with your factory rack, and there's no way to carry 98 lbs of SUP/Kayak on a rack that has a 100 lb capacity - any carrier is going to overextend the rack. So your only option truly is a trailer, and here are the parts you'll need: -...
  view full answer...
• Trailer Hitch Recommendation for 2008 Chevy Cobalt Sedan
  First place to check is the how many doors do you have? 2 doors equals coupe and 4 equals sedan. Do you see any badges at the rear of the vehicle on the trunk that say SS or Sport? If you can get back to me with that info I can see what you'd need.
  view full answer...
• Will the Draw-Tite Sportframe # 24794 Fit a 2018 Nissan Sentra
  We do have a trailer hitch that is confirmed as a fit for your 2018 Nissan Sentra but the Draw-Tite Sportframe # 24794 only fits Nissan Sentra models from 2007-2012. For your 2018 you need the Draw-Tite Sportframe # 24907 instead. You will also need wiring # 118582, a draw bar like part # 3593, and a hitch ball like 1-7/8" part # 19256 or 2" part # 19258. Be sure to follow any instructions in your owner's manual regarding towing with your vehicle.
  view full answer...
• Trailer Hitch for 2015 Tesla Model S for Carrying Bike Rack or Towing
  What year Model S do you have?
  view full answer...
• Recommended Hitch for a 2024 Honda Civic
  Yes, it does so long as yours doesn't have center exhaust. The Curt Trailer Hitch item # C92UR has been confirmed to fit both the hatchback and sedan models of the 2024 Honda Civic. This hitch is custom fit and bolts to your Honda with included hardware. The Curt item # C92UR is a class I hitch with a 1-1/4" receiver. It has a 2,000 lbs towing capacity and a 200 lbs maximum tongue weight. I have attached a couple of pictures below along with an installation video to help you get this...
  view full answer...
  
• Recommended Hitch for a 1997 Ford Mustang GT w/ Dual Exhaust
  No, that one won't but I have one that will. It is the Draw-Tite Trailer Hitch item # 24687. This hitch is confirmed to fit the 1997 Ford Mustang GT with dual exhaust. This is a class I hitch with a 1-1/4" receiver. This is the highest capacity hitch available for your car. I have attached a couple of pictures below of this hitch installed on a Mustang GT with dual exhaust. I have also linked an installation video to help you get it set up. The Curt Hitch item # C11041 you were looking...
  view full answer...
  
• Does the Heat Shield Have to Be Removed to Install the Curt C23HR on a 2021 Hyundai Sonata?
  I can confirm that the heat shield will have to be removed to install the Curt Trailer Hitch item # C23HR on your 2021 Hyundai Sonata. The heat shield mounts on the frame where the trailer hitch will sit so it has to go. I have attached a screenshot below from the instructions so you can see this step. All the heat shield does is block the heat from the muffler. Once the hitch is in its place the steel does a far superior job of keeping exhaust heat away from your car. If you are planning...
  view full answer...
  
• Recommended Hitch and Wiring Harness for a 019 Honda Accord Touring Hybrid
  To add a hitch to your 2019 Honda Accord Touring hybrid, you will need the Draw-Tite Trailer Hitch item # 24972 you were looking at. This hitch is custom fit and bolts to your Honda with included hardware. This is a class I hitch with a 1-1/4" receiver and the only available option for the hybrid models. I have linked an installation video below. To add a 4-way connector to your Honda, I recommend the Curt T-Connector Vehicle Wiring Harness item # C56402. This custom fit wiring harness...
  view full answer...
• Does the Curt Hitch C67FR Fit a 2024 Kia Soul?
  Yes, it does unless yours is the 1.6L turbo model! The Curt Hitch item # C67FR has been confirmed to fit the 2024 Kia Soul. This hitch is custom fit and bolts to your Kia with included hardware. The Curt item # C67FR is a class I hitch with a 1-1/4" receiver. It has a 2,000 lbs towing capacity and a 200 lbs maximum tongue weight. I have attached a couple of pictures along with an installation video so you can see what this hitch looks like when installed. If you are planning on towing...
  view full answer...
  
• Is there a 2 Hitch for a 2023 Kia Seltos?
  No, there is not. The only hitch available for the 2023 Kia Seltos is the Curt item # C65FR. This is a class I hitch with a 1-1/4" receiver. It has a 2,000 lbs towing capacity and a 200 lbs maximum tongue weight. I really like this hitch because the crosstube mounts completely behind the rear bumper leaving only the 1-1/4" receiver exposed. This not only looks better but it helps with ground clearance. I have attach a couple of pictures below along with an installation video so you...
  view full answer...
  
• Will the Curt Hitch C11402 Fit the 2020 Kia Optima SX w/ Dual Exhaust?
  Yes, it will! The Curt Hitch item # C11402 is confirmed to fit all models of the 2020 KIA Optima including the SX which has dual exhaust. This hitch is custom fit and bolts to your Kia with included hardware. The Curt Hitch item # C11402 is a class I hitch with a 1-1/4" receiver. It has a 2,000 lbs towing capacity and a 200 lbs maximum tongue weight. I have linked an installation video below to help you get it set up. If you are planning on towing you will also need a wiring harness...
  view full answer...
• Does this Hitch Fit a 2011 Suzuki SX4?
  Yes, it will so long as you have the hatchback model. The Draw-Tite Hitch item # 24817 is confirmed to fit the 2011 Suzuki SX4 hatchback. It looks like the crossover model is consider a hatchback. If your Suzuki is a sedan you would need the Curt Hitch item # C11446. If you are planning on towing you will also need a wiring harness item # 56002 and the Draw-Tite Drawbar item # 3593 and then for hitch balls item # 19258 for a 2 inch ball or item # 19256 for a 1-7/8 inch ball.
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?