Trailer Hitch Ball Mount - Fits 1-1/4 Inch Hitch

...loads. If you are interested in a hitch mounted bike rack then I recommend the Thule Hitching Post Pro # TH934XTR. Not only does it feature the ability to fit on both 1-1/4 inch and 2 inch hitches...

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

...exactly with a 2-1/2" hitch receiver is the one I mentioned above which has a 7" rise/drop. Since you need less than this it will work out just fine for your towing application. Then for an anti-rattle pin...

Hey James! The individual balls can not be removed on the BulletProof Hitches Aluminum Adjustable 2-Ball Mount item #BPH47MR. The platform they are mounted on can be removed by taking the pins out holding it to the shank but the balls are permanently…

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

Hello Paul, thanks for reaching out. The inside dimension of the Curt Heavy-Duty Dual Ball Attachment for Weight Distribution Shanks #C29NR is 2". It will work with any standard weight distribution shank. I edited a picture to illustrate.

The Curt Rebellion XD part #C57UR measures 10 inches from the bottom of the shank that inserts into the hitch opening to the bottom of the ball mount. So you would lose 10 inches of ground clearance measured from bottom of your hitch.

Great question Luke! These are all great options, but let me point out a few differences for you. The etrailer Adjustable 2-Ball Mount #e66PR is a good quality, affordable option compared to similar options like the BulletProof Hitches 2-Ball Mount…

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

...what is the dimensions from the front of the mounting plate to the back of the pump enclosure? I have a Lamar dump trailer with the V shaped box on the hitch. Im wondering if this jack will fit...

...loads. If you are interested in a hitch mounted bike rack then I recommend the Thule Hitching Post Pro # TH934XTR. Not only does it feature the ability to fit on both 1-1/4 inch and 2 inch hitches...

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

...exactly with a 2-1/2" hitch receiver is the one I mentioned above which has a 7" rise/drop. Since you need less than this it will work out just fine for your towing application. Then for an anti-rattle pin...

Hey James! The individual balls can not be removed on the BulletProof Hitches Aluminum Adjustable 2-Ball Mount item #BPH47MR. The platform they are mounted on can be removed by taking the pins out holding it to the shank but the balls are permanently…

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

Hello Paul, thanks for reaching out. The inside dimension of the Curt Heavy-Duty Dual Ball Attachment for Weight Distribution Shanks #C29NR is 2". It will work with any standard weight distribution shank. I edited a picture to illustrate.

The Curt Rebellion XD part #C57UR measures 10 inches from the bottom of the shank that inserts into the hitch opening to the bottom of the ball mount. So you would lose 10 inches of ground clearance measured from bottom of your hitch.

Great question Luke! These are all great options, but let me point out a few differences for you. The etrailer Adjustable 2-Ball Mount #e66PR is a good quality, affordable option compared to similar options like the BulletProof Hitches 2-Ball Mount…

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

...what is the dimensions from the front of the mounting plate to the back of the pump enclosure? I have a Lamar dump trailer with the V shaped box on the hitch. Im wondering if this jack will fit...