Popular Brands By Category

Towing

Sports & Recreation

Trailer

Vehicle

RV & Camper

What our customers are saying:

WOW! I compared prices with a local dealer and saved $85 over 25% on my purchase and had it delivered to my door.

Brent

New Smyrna Beach, FL


maxxair





Maxxair Reviews and Installation Videos


Expert Answers about Maxxair

  • Availability of AC Shroud to Fit a Coleman Mach AC Unit
  • Yes, the MaxxAir shroud part # MA00-325001 is a fit for the Coleman Mach, Mach 1, Mach 3 and Mach 15 models and mounts like the original and includes mounting hardware and instructions. I attached a review video for this for you to check out as well.
    view full answer...

  • Troubleshooting MaxxAir MaxxFan 12V Fan-Powered Trailer Roof Vent That Beeps
  • My contact at MaxxAir advised that there are three potential causes for the beep and no fan motion you're experiencing with your MaxxFan Trailer Roof Vent # MA00-04000K. One potential cause is that the unit was wired with incorrect polarity. Make sure the white wire is grounded and the black wire is connected to your 12V power source (of at least 5-amps). Another possible reason for the malfunction is low incoming voltage. Use a voltmeter like # BTMT15 to make sure your battery is delivering...
    view full answer...

  • Amp Draw of MaxxFan Deluxe RV Fan
  • While running the MaxxAir MaxxFan Deluxe # MA00-06401K requires about 4-1/2 amps. For startup it will pull around 9 amps.
    view full answer...

  • Which is Quieter the MaxxAir Trailer Roof Vent or the Fan-Tastic Vent Roof Vent
  • The MaxxAir vent # MA00-06401K and the Fan-Tastic Vent roof vent # FV801250 will be close to the same decibel level when running but I give a slight edge to the MaxxAir because it moves a little less air (900 cubic feet per minute versus 920 on the Fan-Tastic) and because it has a sealed ball bearing 12 volt motor which would theoretically be quieter. Honestly you may not be able to tell the difference. As far as wind noise on the exterior I would go with the MaxxAir vent again since...
    view full answer...

  • Replacement A/C Shroud for Older Coleman-Mach 8330 Series A/C Unit on 1999 Exiss Horse Trailer
  • The MaxxAir TuffMaxx Replacement Shroud # MA00-325001 that you referenced will work well on your horse trailer's A/C unit. I spoke with my contact at MaxxAir and Coleman-Mach and confirmed the replacement shroud will fit your unit. Based on my research, your model number 8333-871 is an older model Coleman-Mach air conditioning unit. The current model number that corresponds with your unit's model number is 48203C966. This model number is a Mach 3 Plus unit.
    view full answer...

  • Recommended Vent Fan for Truck Cap to Allow Ventilation for Dogs
  • The MaxxAir MaxxFan Plus - Smoke # MA00-04500K will work on your fiberglass truck cap, but highway speeds will not allow it to stay open. The remote will work fine from inside you truck cab. If you want to be able to drive the highway speeds, I recommend the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - Smoke # MA00-07500K. This will keep your dogs safe as long as you have the 12V power on even when you are away from your vehicle. This will...
    view full answer...

  • How Much Amperage Does the MaxxAir MaxxFan # MA00-07500K Draw
  • The 900 CFM fan of the MaxxAir MaxxFan # MA00-07500K that you referenced needs to be attached to at least a 5 amp circuit.
    view full answer...

  • Replacement AC Shroud for Coleman Mach RV Air Conditioner
  • Part 8333-4161 refers to a shroud for a series of Airxcel AC units. We do not offer this exact part number but our MaxxAir TuffMaxx Replacement Shroud # MA00-325001 is almost an exact match to your dimensions and is a confirmed fit for Mach 1, Mach 3 and Mach 15 models. Please refer to the linked photo for dimensions. Keep in mind that these shrouds generally have a good bit of flex to them and so a cover whose dimensions may vary slightly from the original can often still work fine.
    view full answer...

  • Troubleshooting MaxxAir Vent Fan that Won't Turn On and Rain Sensor Light On
  • I spoke with my contact at MaxxAir regarding your vent like the MaxxFan # MA00-04500K. He said what you are experiencing might be caused by a short in the rain sensor. Since that light is coming off and on, this is likely the issue and what is also causing the fan not to turn on. He recommended taking a rag with some rubbing alcohol and simply cleaning out this sensor. Hopefully once it is cleaned out, everything should start working again as normal. If you are still having issues,...
    view full answer...

  • Wire Size Used to Install MaxxFan Deluxe Roof Vent w/12V Fan & Thermostat MA00-05100K
  • The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 10 Speed - White Item # MA00-05100K only requires 12 volt, 5 amp power to operate so based on this 12 gauge wire would be overkill but 16 gauge such as # DW02359-1 sold by the foot is more ideal.
    view full answer...

  • Hardware Needed to Install MaxxFan Deluxe Roof Vent # MA00-05100K
  • The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat # MA00-05100K referenced in your question includes the white interior trim piece (garnish), insulated electrical connectors and the hardware needed for installation. The only thing you will need to add is some roof sealant # 0160297 and 16 gauge wire like # DW02359-1 if you don't already have it. The wire is sold by the foot so you can get exactly the length you need. This is a really nice roof vent with fan that will move air in...
    view full answer...

  • What is the Difference Between the MaxxAir and Camco RV Vent Covers
  • Both the MaxxAir Standard RV and Trailer Roof Vent Cover part # MA00-933066 and the Camco RV and Enclosed Trailer Roof Vent Cover w/ Detachable Louvered Screen part # CAM40431 are designed to fit 14" x 14" roof vents. The overall dimensions of the MaxxAir is 19" long x 18-1/2" wide x 9-1/2" tall and the overall dimension of the Camco RV is 18-1/2" long x 18" wide x 9-1/2" tall. Both of these roof vent covers come with mounting hardware and have a removable louvered vent for easy cleaning....
    view full answer...

  • Does the MaxxAir MaxxFan Deluxe have a Rain Sensor
  • For a trailer roof vent that has a rain sensor you can use # FV803350. I have linked a video review of this fan for you. The MaxxAir MaxxFan Deluxe # MA00-07500K does not have a rain sensor but does have a large rain shield to keep out rain. I have linked the instructions which cover installation as well as features of the fan. These fans fit all standard 14-1/4 by 14-1/4 inch openings.
    view full answer...

  • How Do You Remove The Screen On the MaxxAir MaxxFan?
  • To remove the screen for the MaxxAir MaxxFan Trailer Roof Vent w/ 12V Fan - Manual Lift - 14-1/4" x 14-1/4" - White, # MA00-04000K, you simply remove it from the 4 mounting tabs. These tabs rotate. I've attached a picture for you.
    view full answer...

  • Amperage Draw Of MaxxFan Deluxe Roof Vent w/ 12V Fan # MA00-06401K
  • I called my contact at Maxxair and asked about the amp draw for the Deluxe Roof Vent w/ 12V Fan, part # MA00-06401K. They told me the amp draw per the 4 speed settings is as follows: 1 - 2.3 amps 2 - 4.8 amps 3 - 1.83 amps 4 - 4.2 amps.
    view full answer...

  • Are Fan Blades Clear on MaxxAir MaxxFan Deluxe Fan MA00-07500K
  • Yes, the fan blade in the MaxxAir MaxxFan Deluxe Fan # MA00-07500K is clear non-tinted plastic and the exterior lid is clear also but is smoke-tinted. I went to our warehouse and inspected one of these units to confirm.
    view full answer...

  • Installing MaxxAir MaxxFan Deluxe - Smoke # MA00-07500K
  • The MaxxAir MaxxFan Deluxe - Smoke # MA00-07500K referenced in your question will fit all standard 14 inch x 14 inch roof openings. If this is what you have in the roof of your RV, then this will work great. This unit will include both the roof mounting flange and hardware, so nothing else will be needed. I recommend using the included mounting flange and new putty/caulk in order to provide the best seal and installation. This is a great 12V fan with the remote controlled fan speed...
    view full answer...

  • What is the Height of the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K
  • The lift that you are speaking about (pointed out in the attached picture) for the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K is the interior trim, or otherwise known as the garnish. This is actually the piece that takes up the space that is from the inside ceiling to your roof - it will not add extra height to the vent on top of your roof. You can install the vent without the garnish, however, it will leave anything between your ceiling and roof exposed on the inside of your trailer...
    view full answer...

  • Installing the MaxxAir MaxxFan Trailer Roof Vent # MA00-05100K
  • The MaxxAir MaxxFan Trailer Roof Vent w/ 12V Fan # MA00-05100K referenced in your question will simply connect to your RV's 12-volt wiring. Using the insulated electrical connectors provided with the Roof Vent, you will connect the RV's 12 volt power to the two power wires located on the driver side of the MaxxFan. The black wire on the MaxxFan that is identified with a tag showing (+) will be connected to the vehicle 12 volt (+) positive supply. This is a great vent with a variable-speed...
    view full answer...

  • Max Roof Vent Cover Opening for RV's
  • I spoke to my contact at MaxxAir and they informed me that they do not make a vent cover that will allow a roof vent to open the full 12". They were also unaware of another manufacture who does as the 10" height of most roof vent covers is more or less an industry standard. I recommend using the MaxxAir II RV and Enclosed Trailer Roof Vent Cover part # MA00-933072 for white, part # MA00-933075 for black, or part # MA00-933073 for smoke. This roof vent cover will allow for you to open...
    view full answer...

  • Adding an In-Line Fuse to Maxxair Deluxe
  • The MaxxAir MaxxFan Deluxe # MA00-07500K would require a 5 amp fuse.
    view full answer...

  • MaxxAir Vent Cover for a Ventline E-Z Lift Roof Vent
  • For the Ventline E-Z lift vents you will need to use a regular MaxxAir vent cover, # MA00-933067. As you have found the MaxxAir II covers are not a direct fit. I have linked a video review for you.
    view full answer...

  • The MaxxAir Mini Deluxe Trailer Roof Vent w/ 12V Fan # MA00-03801 Fan CFM
  • The CFM rating for the fan in the MaxxAir Mini Deluxe Trailer Roof Vent # MA00-03801 that you referenced is 200.
    view full answer...

  • Troubleshooting Two Maxxair Deluxe Vents on a Sprinter Van
  • If you are getting no power at all when you hit the on/off button on either of your MaxxFan Deluxe Roof Vent w/ 12V Fan - Manual Lift - 4 Speed - Smoke # MA00-06401K vents, then there is most likely not power getting to them. I recommend using a circuit tester like # 3808 to check for power as it is very likely they are run to a different location than your lights. There are multiple functions on these fans, so if none of them are working, then the unit will need to be replaced. Even...
    view full answer...

  • Available Solar-Powered Trailer Vents
  • We do carry solar-power products and accessories as well as a wide range of trailer roof vents, including the MaxxAir 12V vent/fan unit # MA00A04401K. All 12V fan-powered trailer roof vents are shown on the linked page and most of these are the standard 14 x 14-inch size. We do offer solar-power vents for RV refrigerators from Camco, parts # CAM42165 and # CAM42162 but not solar-powered full-size trailer vents like the MaxxAir. We DO have stand-alone solar panels like the 200-watt...
    view full answer...

  • Recommended Vent Cover For MaxxAir MaxxFan To Allow Travel Speeds With Open Vent
  • There are no posted speed restrictions on this MaxxAir MaxxFan - White, # MA00A04301K, so I called the manufacturer to see if they have recommendations. Their tech said they don't test those lids to see what speeds they can handle, but it is likely that highway speeds with a crosswind could rip the lid off the unit. If you want to protect your vent for travel and from rain to allow that vent to be open, you will want the # MA00-933072 or the # FVU1500WH roof vent cover.
    view full answer...

  • Remote Control Operation of MaxxAir MaxxFan Deluxe 12V Trailer Vent MA00-07500K
  • My contact at MaxxAir confirmed that if you install two of their MaxxFan Deluxe # MA00-07500K in your Sprinter you can use either remote control to operate both fans. The remotes are programmed the same so the one from one fan will still work the other fan too so long as there is a line-of-sight between the remote and the sensor on the vent. You do not have to program or pair the remote with the fans. This means you can use one remote and keep the other in a safe place as a spare. For...
    view full answer...

  • MaxxAir Trailer Roof Vent Cover MA00-933075 for 2016 Forest River Sandpiper 381 RBOK 5th Wheel
  • The MaxxAir II RV and Enclosed Trailer Roof Vent Cover # MA00-933075 is a great way to protect your RV interior from water and at the same time allow you to use the RV's standard-size 14 x 14-inch roof vent even in bad weather. The MaxxAir cover measures 22-1/8" long x 20-1/8" wide x 9-3/8" tall so it fits over any such roof vent and allows it to remain open. Based on my research your 2016 Forest River Sandpiper 381 RBOK 5th wheel uses the standard 14 x 14 vent so this MaxxAir cover...
    view full answer...

  • Troubleshootinng MaxxFan Roof Vent that Keeps Beeping
  • Are you having issues with a MaxxAir MaxxFan roof vent like # MA00-04000K? It could be an internal issue with the fan and it needs to be replaced. Before replacing you can check a couple of things. Is it a new install? If so make sure you have the wiring correct and not reversed. The white wire should be grounded and black to 12 volt power. If the wiring is correct make sure it's getting sufficient power and the connections are good. If both of these check out you likely have...
    view full answer...

  • Will the MaxxFan Deluxe # MA00-07500K Fit in Place of the MaxxFan # MA00-06200K
  • It sounds like you have the MaxxAir MaxxFan # MA00-06200K on your Jayco North Point. The MaxxFan and the MaxxFan Deluxe # MA00-07500K are the exact same roof vent, the Deluxe version just has more features. The garnish, or flange, that fits one is compatible with the other so you will be good to go. The Deluxe version comes with a flange as well in case you find that the current garnish needs to be replaced after removing the MaxxFan.
    view full answer...





^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
71

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.