Hey Jim. You can email whatever pictures you'd like me to look at directly to the email address you receive this response from. We do have a couple of wiper seals that are close to the measurements you have described. I've listed them below:…
Harvey, you’re right on target asking about sizing. The AFMD35121 was a 35k BTU unit that’s been discontinued. You can step into the 35K BTU #DMC74MR furnace by Dometic, but it is 2 inches taller than your current one. Most folks just enlarge the…
The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Eric, thanks for the information! Your older GE ARC13AACBL2 with 410a refrigerant is not going to be compatible with any AC components that came out this year. Everything has the new R32 refrigerant now so it's made all the 410a systems and…
Hey Bill thanks for the information. The C865H-9/16 in that axle tag number means you have 8 on 6-1/2 hubs with 9/16" lug studs. The Hydrastar item #HSE7K-T1, you were looking comes with 1/2" lug studs. You'll need the Hydrastar Disc…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
Yes, if you just need the motor from the Lippert Replacement RV Slide-Out Venture Actuator with 18:1 Motor #LC119128 then you'll need to get the following: - Replacement 18:1 High Speed Motor Assembly #LC295380
Hey Brad, thanks for reaching out! What are the dimensions of your tail lights? The numbers and letters you gave me have to do with the testing that the lights have undergone as opposed to a part number. Let me know what measurements you find!
The piece you're referring to in the #LC26VR kit is called a "shoe". This part is plastic with foam pads on each end that helps cushion the motor bracket as it slides back and forth to either end of the track.
The Fixed Dual Rack Repair Kit #LC84FR goes on the left side of the slide as you look at the slide out from the outside of the camper. So on the drivers side it will be the front of the slide. The Floating Dual Rack Repair Kit #LC26VR is going to be…
...electric through-frame slide out, and it measured 24" long, then you could use the Lippert Replacement RV Slide-Out Venture Actuator with 18:1 Motor # LC119128.
The replacement slide out parts listed...
Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…
Hey Jim. You can email whatever pictures you'd like me to look at directly to the email address you receive this response from. We do have a couple of wiper seals that are close to the measurements you have described. I've listed them below:…
Harvey, you’re right on target asking about sizing. The AFMD35121 was a 35k BTU unit that’s been discontinued. You can step into the 35K BTU #DMC74MR furnace by Dometic, but it is 2 inches taller than your current one. Most folks just enlarge the…
The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Eric, thanks for the information! Your older GE ARC13AACBL2 with 410a refrigerant is not going to be compatible with any AC components that came out this year. Everything has the new R32 refrigerant now so it's made all the 410a systems and…
Hey Bill thanks for the information. The C865H-9/16 in that axle tag number means you have 8 on 6-1/2 hubs with 9/16" lug studs. The Hydrastar item #HSE7K-T1, you were looking comes with 1/2" lug studs. You'll need the Hydrastar Disc…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
Yes, if you just need the motor from the Lippert Replacement RV Slide-Out Venture Actuator with 18:1 Motor #LC119128 then you'll need to get the following: - Replacement 18:1 High Speed Motor Assembly #LC295380
Hey Brad, thanks for reaching out! What are the dimensions of your tail lights? The numbers and letters you gave me have to do with the testing that the lights have undergone as opposed to a part number. Let me know what measurements you find!
The piece you're referring to in the #LC26VR kit is called a "shoe". This part is plastic with foam pads on each end that helps cushion the motor bracket as it slides back and forth to either end of the track.
The Fixed Dual Rack Repair Kit #LC84FR goes on the left side of the slide as you look at the slide out from the outside of the camper. So on the drivers side it will be the front of the slide. The Floating Dual Rack Repair Kit #LC26VR is going to be…
...electric through-frame slide out, and it measured 24" long, then you could use the Lippert Replacement RV Slide-Out Venture Actuator with 18:1 Motor # LC119128.
The replacement slide out parts listed...
Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Enhance Your RV Experience with Lippert Slide-Out Systems
Lippert Through-Frame Slide-Out Systems are a reliable choice for RV enthusiasts looking to replace or upgrade their slide-out parts. Known for their durability and ease of installation, these systems ensure smooth operation and longevity, making them a f
Yes, Lippert slide-out systems are designed with ease of installation in mind. Many RV owners find them straightforward to install, making them a great option for those who prefer DIY projects. Their compatibility with various RV models adds to their appeal.
These systems enhance RV functionality by providing more power and quieter operation compared to older models. They ensure your slide-out extends and retracts smoothly, even in challenging conditions like strong winds, offering peace of mind during your travels.
Lippert systems stand out for their combination of affordability and performance. They often come at a lower price point than competitors while still delivering excellent functionality and durability, making them a smart investment for RV enthusiasts.
Lippert systems are praised for their precise fit and reliable performance. They offer a seamless replacement for worn-out parts, ensuring your RV slide-out operates smoothly. Their robust construction and ease of installation make them a go-to for RV owners seeking long-lasting solutions.
Lippert slide-out systems are built to last, with many users reporting years of reliable service. They are crafted to withstand the rigors of frequent use, ensuring your RV slide-out remains functional and efficient over time, even in older RV models.
Filters
