Hey Jon, the Taylor Made Gas Shock part #3691828 that you referenced has a compressed length of 9.5 inches and an extended length of 15 inches. Would that work for you?
Hey Pam, welcome back! To replace your Pentair Shurflo Revolution 4008 Series By-Pass Pump, I recommend the Seaflo Diaphragm Pump for Boats and RVs item #SE57FR. This is a 12v powered three gallon per minute pump that is rated up to 55 psi. It works…
Hi Tom; the Taylor Made Marine Gas Strut for Boat Hatches - 10 mm Socket - 10 lb Force - 10" Long - Steel #3691822-10 measures 7" on center when compressed.
Hey Nicole! With the weight of the mattress and the plywood you're probably at 140-160 lbs. You have two shocks for support, and you want the shocks to be 10-30% stronger to make sure they can lift the mattress without any issues. Based on that,…
Hey Ray! What you’re seeing is pretty typical after going to a thicker foam mattress. The weight might not be drastically higher, but the leverage is, so the 60 lb struts end up feeling underpowered. If the 60 didn’t do it, the 80 lb #RD44MR is…
Welcome back John. The most important thing you'll need to know is how heavy your bed and the base it's sitting on weighs so you can get the right strength strut. Once you figure that out you can measure the length of your storage area and…
All of the Replacement Round Spring Bars for the Fastway e2 Weight Distribution systems, #FA94-02-1099, #FA94-02-0899, and #FA94-02-0699, measure 31-1/2 inches long. The diameter of the bar at the upper end is 1.39 inches, and the inside groove…
Hi BO; are you using two gas struts underneath the mattress to lift it? Assuming you are, the #372-2300-120 with a force of 120 lbs is too much. You want to use the Gas Shock - 60 lb Force - 20" Extended, 11.41" Compressed - Black Nitride…
The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…
Sure thing; the MaxxFan Deluxe Roof Vent #MA00-06401K has only four speeds and does not have a thermostat so you have to manually set the air speed. The MaxxFan Deluxe Roof Vent #MA00-06200K has 10 speeds and includes a thermostat which will…
The High Pointe microwave part #HP49ZR would work great as a replacement for what you have now as it's the correct dimensions and also works great. We also have it in black with the part #HP99ZR.
Hello again Daniel, The B-W (B-W Manufacturing / Parallax) 6300 Series Model 6345 is an older converter/charger unit designed primarily for lead-acid batteries, such as flooded or AGM deep cycle batteries. These older converters typically charge at a…
Hey Jon, the Taylor Made Gas Shock part #3691828 that you referenced has a compressed length of 9.5 inches and an extended length of 15 inches. Would that work for you?
Hey Pam, welcome back! To replace your Pentair Shurflo Revolution 4008 Series By-Pass Pump, I recommend the Seaflo Diaphragm Pump for Boats and RVs item #SE57FR. This is a 12v powered three gallon per minute pump that is rated up to 55 psi. It works…
Hi Tom; the Taylor Made Marine Gas Strut for Boat Hatches - 10 mm Socket - 10 lb Force - 10" Long - Steel #3691822-10 measures 7" on center when compressed.
Hey Nicole! With the weight of the mattress and the plywood you're probably at 140-160 lbs. You have two shocks for support, and you want the shocks to be 10-30% stronger to make sure they can lift the mattress without any issues. Based on that,…
Hey Ray! What you’re seeing is pretty typical after going to a thicker foam mattress. The weight might not be drastically higher, but the leverage is, so the 60 lb struts end up feeling underpowered. If the 60 didn’t do it, the 80 lb #RD44MR is…
Welcome back John. The most important thing you'll need to know is how heavy your bed and the base it's sitting on weighs so you can get the right strength strut. Once you figure that out you can measure the length of your storage area and…
All of the Replacement Round Spring Bars for the Fastway e2 Weight Distribution systems, #FA94-02-1099, #FA94-02-0899, and #FA94-02-0699, measure 31-1/2 inches long. The diameter of the bar at the upper end is 1.39 inches, and the inside groove…
Hi BO; are you using two gas struts underneath the mattress to lift it? Assuming you are, the #372-2300-120 with a force of 120 lbs is too much. You want to use the Gas Shock - 60 lb Force - 20" Extended, 11.41" Compressed - Black Nitride…
The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…
Sure thing; the MaxxFan Deluxe Roof Vent #MA00-06401K has only four speeds and does not have a thermostat so you have to manually set the air speed. The MaxxFan Deluxe Roof Vent #MA00-06200K has 10 speeds and includes a thermostat which will…
The High Pointe microwave part #HP49ZR would work great as a replacement for what you have now as it's the correct dimensions and also works great. We also have it in black with the part #HP99ZR.
Hello again Daniel, The B-W (B-W Manufacturing / Parallax) 6300 Series Model 6345 is an older converter/charger unit designed primarily for lead-acid batteries, such as flooded or AGM deep cycle batteries. These older converters typically charge at a…
Gas struts at 10-1/2 inches long are ideal for various applications, offering a perfect fit for your projects. Whether you're replacing old struts or working on a new build, these struts provide reliable support and smooth operation.
These struts are perfect for applications requiring precise support and smooth motion. Their length makes them versatile for various projects, ensuring a snug fit and reliable performance.
Ideal for automotive hoods, cabinets, and other projects needing controlled lifting and lowering. Their size ensures they fit snugly, providing the right amount of force and stability.
They offer consistent force and smooth operation, making them perfect for projects where precision and reliability are key. Their design ensures they handle repeated use without losing effectiveness.
Yes, these struts are designed for straightforward installation. With the right tools, you can easily replace or install them, ensuring a secure fit and optimal performance.
Their precise length and robust construction ensure they fit perfectly in designated spaces, providing the necessary support and smooth operation for various applications.
Filters
Gas Struts Parts or Accessories
