Hole Size Dimension for Optronics LED Tail Light with Grommet

Question

Question:

What is the hole size for the light and rubber grommet to fit in?

asked by: Brett B

1

Helpful Expert Reply:

The light dimensions of the Optronics LED # TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template they sent to assist.

expert reply by: Jason S

1

click to enlarge

Bill

5/21/2024

Jason, The spec shows 1-3/4" overall depth of the light but your answer states 3/4"deep. Does the 1-3/4" depth include the connector for the wiring? I am planning on installing these into 4 x 2 x 3/16" wall rectangular tubing but I only have 1-5/8" inside the tubing to work with. I might be OK because the face of the light sticks out from the face, but I am not sure by how much. Thank you for the help in advance. Bill

Jon G.

5/28/2024

@Bill Jason had a typo and it should have read as 1-3/4", which I have since corrected. This measurement is taken from the face of the light assembly to the back where the connector is installed. The light housing piece is about 1" thick though and since these install with about half of the housing sticking out you'll have enough room for the connector - I just recommend using one that has an angle like the part # A47PB. You can find a photo showing the dimensions of this light kit on the product page directly.

Answer 1

I can help you add reverse lights to your trailer. Yes, It is important to pay attention to DOT compliance when adding lights on your boat trailer. Compliance will be met if you use the Optronics #BUL10CB light as your backup light. The #BUL72CB is…

view full answer...

Answer 2

If you are looking to replace your current OPT STL 82-RCB, we actually have this exact light available. The Optronics LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 10 Diodes - Oval - Clear Lens #STL82RCB will be the exact replacement you…

view full answer...

Answer 3

Yes, the difference is that the BUL72CBGK has the grommet included. To replace both the light and grommet you will need #BUL72CB and #A70GB. I looked at a few images of MasterCraft Trailers and while we don't have the exact information of what it…

view full answer...

Answer 4

Hey Kent, it looks like the closest you can use for a replacement that we have is the Optronics Fleet LED Trailer Tail Lights w/ Grommets #TLL12RK. These lights measure 7-9/16" long x 3-5/16" tall x 1-3/4" thick, has the three prong…

view full answer...

Answer 5

The Optronics LED Trailer Tail light - Stop, Tail, Turn - Submersible - 10 Diodes - Red Lens #STL72RB will use the PVC Grommet for 6-1/2" Oval Trailer Tail Lights #A70GB for mounting. With this combination the opening you need to cut is a…

view full answer...

Answer 6

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 7

I had our warehouse measure the Curt Trailer Hitch Receiver #C15703 you were looking at, and has an overall width of 40-5/8", overall length of 29". The distance between the vertical mounting holes is 14-1/2" center to center, and the…

view full answer...

Answer 8

The Bright Way Push-to-Test Trailer Breakaway Kit #3802311 that you referenced comes with a 10 amp hour battery. I attached a picture of the battery outside of the box for you to check out as well. I attached a review video for this kit for you to…

view full answer...

Answer 9

I wonder if the box was stressed in some way when bolting it to the trailer. Maybe one of the install bolts was pulled the box in a direction that stressed it. That said, for just the box you'd want the part #3375601101 which is an exact…

view full answer...

Answer 10

Those are the wires for the brake magnets. You will need to connect the black wire to the brake controller output wire on your trailer connector and you are correct the white wire will need to be grounded to a clean metal surface on the trailer. I…

view full answer...

Answer 11

Hi David; I honestly wouldn't choose steel brake lines for a salt water application, even if they were stainless. A better option would be the Hydrastar Hydraulic Brake Line Kit #HS496-152 or #HS496-252 with copper-nickel alloy. This has proven…

view full answer...

Answer 12

Grounding through the ball doesn't work well, as you've found. If the current harness doesn't have a ground circuit, the wiring must be fairly old as it's pretty typical for a trailer connector to have a ground circuit. The fact that…

view full answer...

Hole Size Dimension for Optronics LED Tail Light with Grommet

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching