Trailer Tail Light Replacement Recommendation for TecNiq 16P2S2T2T60

Question

Question:

Here is a picture of the tail light

asked by: Annette Y

0

Expert Reply:

I believe the tail lights you have are the TecNiq T60 lights which are industry standard 6" oval recessed lights. To replace those you can use the Optronics Fleet LED Trailer Tail Lights # TLL12RK.

If your lights look different than this please send in a picture with some dimensions so I can help you find the correct replacements.

expert reply by: Jon G

0

click to enlarge

Annette Y.

6/24/2020

Here is a picture of the tail light

Reply

Jon G.

6/24/2020

Thank you so much for the picture! Since your T60 lights have the 4 mounting locations I recommend using either the 10 diode # STL78RB or 1 diode # STL002RFB as a replacement. The difference between the 2 options is that the 10 diode will be brighter because it has more diode.

Reply

Answer 1

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 2

The Foam Gasket #A32GB is for your LED Clearance or Side Marker Trailer Light in Amber #MCL0032ABB or Red #MCL0032RBB.

view full answer...

Answer 3

Although the Snap-on Reflector Ring, #A78RXB, will not fit the STL178 series lights like the Optronics GLOLight LED Stop/Turn/Tail Light #STL178RFPB, I do have a solution for you. Take a look at the Sealed, 6-1/2" Oval LED Trailer Stop, Turn and…

view full answer...

Answer 4

This sounds like a ground problem on the right side. The turn signal not working makes sense because with the brake lights, there is a constant signal coming through which is enough to make the lights illuminate on both sides like they should. But…

view full answer...

Answer 5

The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…

view full answer...

Answer 6

The Glo-Brite 9553 you have currently measures 6-1/2" x 2-1/4" x 2-1/4" so for an incandescent replacement option I recommend the Custer Trailer Tail Light - Submersible - Stop, Turn, Tail - Incandescent - Oval - Red Lens #G65R which…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hi Gene; we don't have a way of knowing the exact lights on your 2002 Doolittle Cargo Trailer. You will need to measure and compare to the Optronics Fleet LED Trailer Tail Lights #TLL12RK to see if they're a good fit. These lights measure…

view full answer...

Answer 9

Hey Bernie! Yes, the Black Bracket and Single Wire Plug for Thin Line Series Trailer Clearance and Side Marker Lights #A65PB fits both the #MCL63AB and #MCL63RB. This bracket is required for surface mounting. If you need anything else feel free to…

view full answer...

Answer 10

Hey Keith, sorry for confusion but the TecNiq Round Side Marker Light #TN54TR that you referenced does not come with a grommet and you'd need that separately with the part #TN43TR.

view full answer...

Answer 11

Hey Timothy, if the leaf springs have bolt holes on both ends that would mean you have double-eye springs actually. Unless the bolts are on the hangers of the trailer frame? If you can get back to me with that for sure we can determine what you need.…

view full answer...

Trailer Tail Light Replacement Recommendation for TecNiq 16P2S2T2T60

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching