Dutton-Lainson Bolt-On, Drop Leg Trailer Jack - Sidewind - 28-1/2" Lift - 2,500 lbs
(98 reviews)
Price: $167.07
In Stock
Dutton-Lainson Bolt-On, Drop Leg Trailer Jack - Sidewind - 28-1/2" Lift - 2,500 lbs
Item # DL22320
Our Price: $167.07
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (98)
- Q & A (0)
- Photos
Dutton-Lainson Trailer Jack - DL22320
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Utility Trailer
- 2001 - 3000 lbs
- Sidewind Jack
- Weld-On
- Leveling Jacks
- Tongue Jacks
- 28 Inch Lift
- With Rectangle Foot
- Steel
- Dutton-Lainson
Square tube industrial jack is 25-1/4" tall when retracted and offers 15" of screw travel along with an additional 13-1/2" of drop leg extension. Durable zinc plating resists rust and corrosion.
Features:
- Square tube jack lets you raise and lower your boat or utility trailer
- Corrosion-resistant zinc plating
- Sidewind handle
- Bolt-on installation with included hardware
Specs:
- Application: trailer frames up to 3" wide x 5" tall
- Bracket height:
- 10-1/4" Retracted
- 25-1/4" Extended
- Total lift: 28-1/2"
- Travel: 15"
- Drop leg extension: 13-1/2"
- Lift capacity: 2,500 lbs
- Overall height (when retracted): 25-1/4"
- 1-Year limited warranty
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
22320 Dutton-Lainson Model 7201 Square Tube Industrial Jack, Side Wind - 2,500 lb
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- Manufacturer issue
- Arrived Damaged
Customer Reviews
Dutton-Lainson Bolt-On, Drop Leg Trailer Jack - Sidewind - 28-1/2" Lift - 2,500 lbs - DL22320
Average Customer Rating: 4.8 out of 5 stars (98 Customer Reviews)
Square tube industrial jack is 25-1/4" tall when retracted and offers 15" of screw travel along with an additional 13-1/2" of drop leg extension. Durable zinc plating resists rust and corrosion.by: Chris03/30/2023
This review is more for etrailer than the product. I highly recommend etrailer. They were very professional & kind. Product was received sooner than they said. All good things. I installed the trailer jack today and it seems like a good quality piece. It's easy to wind and with the drop leg, it extends high enough for the hitch on my truck. Thank you guys for the great service!
by: Mike05/31/2016
Excellent product - fast delivery. Loved how the video showed a person handling and measuring the product, but what I really wanted to see was what hardware was included and an install demonstration. Either way, the jack works great. I used two of them on my toy hauling pop-up to support the weight of my side-by-side and act as stabilizer jacks.
by: Darren 12/07/2023
Very easy transaction. Fair price and super fast shipping.
Thanks for the good service.
DL
by: Christopher07/19/2023
Poorly packed and hardware was lost as a result.
by: Jeremie05/20/2020
Very happy with my new trailer jack. This is a trailer my dad and I built in 1997. I use it to mainly haul seed for my job. It also gets used for recreation and other stuff. It had a jack with a wheel and was also too short, which meant I had to use a block and lots of wheel chocks. Should have done awhile ago, but never found a suitable jack in stores. I bolted to frame instead of using u-bolts using 6 grade 8 bolts.
by: Andy S09/14/2023
High quality after one year..no rust..smooth! Worth the few extra dollars !$
by: Pietro09/10/2023
Great Jack it's what I expected, Thank you very much
by: Freddie 09/07/2023
Quality product and easy to install
by: Thomas 09/29/2022
I ordered this trailer jack as direct replacement for my Coastline trailer. The jack has worked flawlessly over the last year since my purchase. Buy with confidence.
by: Ronald 06/26/2023
Operates smoothly.
by: Randy S.01/28/2015
This is probably the best buy on the market today for a trailer jack! This jack arrived packed very well with all the hardware needed to install it. it installed on my car trailer in less than an hour in my driveway. It is very well built and thanks to Rose at the order desk I received excellent help in choosing the correct jack for my trailer. If you are buying from someone else, you probably won't get the same quality for your money. Thanks etrailer.com you have me as a lifetime customer.
Randy S.
2/6/2016
he best money I have ever spent for a product. I love the customer service and fast response with shipping...quality product that wont break when you need them!....lifetime customer here! Thanks E-Trailor!
by: Mark S08/14/2016
I have a short shaft on my trailer that could not utilize a conventional trailer jack. The drop leg jack is built well and does the job! I received the jack several days after I ordered it, which was great.
Mark S.
8/14/2017
Great! Well constructed. I have a short shaft on my home made trailer and could not use a conventional trailer jack. This was a great option and it has held up very good. Great product and worth the money!
by: Randy04/16/2012
Yes for anyone looking to replace that old jack this thing rocks.I have a 24 foot cabin cruiser and needed the heavy duty jack with the 23" of lift and this unit fits 100% very smooth and I like the fact that there is not a wheel on it way safer.The install is also way easy.I would highly recommend this for anything with in the 2500# rating .
Randy S.
1/27/2015
Drop leg jack was exactly like described, installed in less than an hour in my driveway. the order was shipped very fast and the jack is every thing you said it was, i am very happy with the jack and e-trailer.Thanks to Rose for the friendly help with my order!
by: Russell06/28/2019
The jack is solid and was very easy to install. It has a grease fitting for future lubrication when needed. The lift was as described in terms of height. All in all this is a very solid Jack which you will enjoy.
Russell
6/29/2020
The jack continues to perform flawlessly
by: James12/22/2016
One of the best investments I've ever made. Looks & works perfect on my aluma cargo trailer. Had it installed in 15 minutes.
James
12/22/2017
Real nice ! 5 stars...
by: Adam B06/22/2017
I purchased this to replace a vintage (think rusty, sticky and generally obstinate) jack. The ordering process was easy, communication from the vendor was excellent and the shipping was fast. Installation took all of about 5 minutes after the rustyjackectomy was performed. The drop leg part of the jack has saved me from carrying around the vintage accessory that came with the jack, a cinderblock to put under the non-functioning wheel at the end of the rustystickobstinate jack. Freedom! There is a smallish foot on the new jack which provides adequate stability and resistance to sinking on soft ground, something that we have lots of here in the Pacific NW. Additionally, this new jack sports a zerk fitting which may help stave off the rustystickyobstinate syndrome that afflicted the original. All in all, this represents a significant improvement to my trailer jacking activities.
by: Mike03/16/2015
This jack was a replacement for a deteriorating jack on my v nose snowmobile trailer. The salt and weather were taking it's toll and the fixed jack was mounted somewhat too low so it occasionally would bottom out on transitions from the road to parking lots. This jack when mounted to my tongue is higher and the drop leg feature still lets me jack it high enought to remove from my truck. Hopefully the Nickel plating will give me a longer service life than the previous painted version that was on my trailer originally. I also like the fact that this jack has a grease fitting to be able to lubricate the internals. Nice jack so far.
by: Alan M.03/11/2020
The jack is great ! Heavy duty and very rugged. The only thing that may be improved is the mounting bar used on the back side of the trailer channel. It needs to be a bit "beefier". My bar bent slightly when I tightened the retaining bolts.
by: John C06/17/2013
Perfect answer to tipping up my boat trailer enough to get bilge to drain.
Used to have to use a cinder block + 2 pieces of wood, crank up the wheel jack (that came on the trailer), put wood under tongue, crank down wheel jack, put in cinder block on its side under wheel, crank up wheel jack, put 2nd (longer) piece of wood under tongue, crank down wheel jack, put cinder block under wheel on it's end (not the most stable arrangement), crank up wheel jack.... it really kinda sucked!!!
Now, I use the wheel jack (that came on the trailer) to detach from tow vehicle and crank it up all the way, Then on the Drop Leg Jack, pull & reposition the pin on drop leg so leg extends fully (2 seconds), and crank up the Drop Leg Jack all the way, done!
by: Todd 01/12/2022
I purchased this jack a year ago for use on a 4 place snowmobile trailer that moves around the salty winter roads of the northeast. Great jack, no rust, powerful jack, smart purchase.
by: Jim01/25/2017
Good heavy jack, easy bolt on mount. Nice leg extension to shorten the cranking to lift the trailer.
Jim
1/26/2018
Still the same. Its working great.
by: Pete S03/22/2012
The sub-standard trailer jacks with a wheel that come with all trailers are junk. They are good for two years before they just won't crank. Their limited adjustment required me to take bottle jacks and blocks of wood to hitch and un-hitch! I highly recommend this product because of it's huge adjustability range, and who needs a wheel on the jack of any boat that weighs more than 3000 lbs! , actually could be hazardous.
Get it , you won't regret it!
by: Ken 02/09/2023
Best one I have bought.
by: Paul Z.11/27/2016
Installed his Jack on a 27 foot deck over snowmobile trailer after going through a fold up styled wheeled Jack a year. After a year it's as sturdy as the day I installed the. Very happy.
by: Dave E.02/21/2017
The wheels and tongue jack I ordered for my boat trailer arrived quickly and well packaged. Thanks to the information on eTrailer pages on how to measure for wheels, the wheels fit the hub perfectly. The trailer jack is not yet installed, but appears to be of good quality. Now, just waiting on the water to warm up to launch the boat and take the grand daughter swimming and boating.
25
98
Show More Reviews
See what our Experts say about this Dutton-Lainson Trailer Jack
- What is the Maximum Height of the Dutton-Lainson Bolt-On, Drop Leg Trailer Jack - Sidewind # DL22320I went to the warehouse and extended the Dutton-Lainson Bolt-On, Drop Leg, Trailer Jack # DL22320 fully. The overall, maximum height available is approximately 33 inches from the footplate to the bottom of the mounting plate. A couple of other dimensions you may be interested in are noted in the picture. The height of the mounting plate is 6-1/2 inches and the width is 6-5/8 inches. The distance from center of the mounting hole to center is 5-1/2 inches. I have attached a FAQ article...
view full answer...
- Trailer Tongue Frame Sizes Dutton-Lainson Trailer Jack , Part # DL22320 will FitI checked with the manufacturer, and Dutton-Lainson trailer jack, part # DL22320 will fit up to a 3 inch frame channel with the bolts provided. If your channel is wider, you would be able to make the jack fit using longer bolts.
view full answer... - Dutton-Lainson Replacement Jack Thanks for the picture! We don't offer replacement parts for what looks like a Dutton-Lainson side mount jack but we do have that jack. It is the Dutton-Lainson Bolt-On, Drop Leg Trailer Jack - Sidewind - 28-1/2" Lift - 2,500 lbs item # DL22320.
view full answer...
- Needing the Bolt Pattern and Dimensons for a Dutton-Lainson Tongue JackI have a solution to your question. For the Dutton-Lainson Bolt-On, Drop Leg Trailer Jack, # DL22320, I have attached a photo of the mounting bracket. We have measured the bracket and the distances of the mounting holes and marked them for you in the picture.
view full answer...
- What is the Bolt Hole Size of the Dutton-Lainson Bolt-On Trailer Jack # DL22320The diameter of the bolt holes on the mounting bracket for the Dutton-Lainson Bolt-On Trailer Jack, # DL22320, is 7/16 of an inch. This jack includes the bolts and additional brackets needed to mount this jack on the trailer frame, so you will not need to provide your own hardware.
view full answer...
- Easy To Use Side Mount Manual Crank Trailer JackWe have a variety of side mount trailer jacks, however, all of which are manual crank. The only electric jacks available are for a-frame trailers. Although we do not have an electric jack that attaches to the side of the trailer frame, we do however have several options with a drop leg feature that will eliminate the need for strenuous cranking. I recommend using the Dutton-Lainson Bolt-On, Drop Leg Trailer Jack part # DL22320 as this has the drop leg feature that will minimize the amount...
view full answer... - Bolt Pattern Of Dutton-Lainson Bolt-On Trailer JackI went to the warehouse and took some measurements of the Dutton-Lainson Trailer Jack, part # DL22320. The mounting flange on the back of the jack has 6 holes. I have attached a photo of the jack and have noted the measurements you asked about. The flange measures 6-1/2 X 6-3/4 inches. It has 6 mounting holes. They are spaced 1 inch apart except the middle two holes on each side. Those are spaced 1-1/8 inches apart. From center of the outside hole to the center of the outside hole on...
view full answer...
- Dimensions of the Inner and Outer Tubes of the Dutton Lainson Jack # DL22320The outer tube of the jack part # DL22320 measures 2-1/4 inches by 2-1/4 inches and the inner tube measures 2 inches by 2 inches.
view full answer... - Trailer Jack that Fits BigTex 70Ch-16 Car HaulerYes, the Dutton-Lainson Bolt-On # DL22320 does fit your frame dimensions of 4 inches tall and 1.5 inches wide. It also has a 2,500 lb capacity so it would work well in that regard as well. I attached a review video for this jack for you to check out as well.
view full answer... - Bolt Pattern of Dutton-Lainson Drop Leg Jack Part # DL22320The bolt holes on the mounting plate of the Dutton-Lainson 2500 lb Drop Leg Trailer Jack, part # DL22320 measure 5-1/2 inches apart, measured center to center. Each of the top three holes is 1 inch apart from the row below it.
view full answer...
- Adjusting the Height of the Bolt-On, Drop Leg Trailer Jack, # DL22320 with Weight on the JackI spoke with my contact at Dutton-Lainson, the manufacturer of the Bolt-On, Drop Leg Trailer Jack, # DL22320, about its functions. The jack can be cranked when there is a load on it to raise and lower the trailer as needed. When the jack is off the ground, you can remove that bottom pin to lower or raise the foot in 3-1/2 inch increments, then replace the pin. This is used so you would not have to do as much cranking. The foot cannot be raised or lowered when the jack has weight applied.
view full answer... - Would the Dutton-Lainson Bolt-On Jack part # DL22320 Fit a Continental Cargo TrailerThe Dutton-Lainson Bolt-On Jack part # DL22320 may be a bit overkill for your trailer as it has a 2,500 lb capacity, but it would work great if that is they type of jack you wanted. I attached a review video for the jack for you to check out as well. The several sets of install holes on the bracket will allow it to fit the frame of your trailer
view full answer... - Sidewinding Square Trailer Jack to Lift a 3,000 Pound Stage to a Height of 32 InchesThe Dutton-Lainson trailer jack # DL22320 would actually work well for your application because it has a drop leg you can lower to achieve an extension of up to 38-3/4 inches. The inner leg, when the handle is turned, has 15 inches of travel, so you would have to extend the jack leg down in order to get the lift you need. The drop leg is held in the inner leg with a pin and has numerous adjustment holes.
view full answer...
- Replacement Washer for 1,250 Pound Dutton-Lainson Trailer JackWhat you need is the Replacement Miter Gear Kit for Dutton-Lainson Trailer Jacks - 1,250 - 2,000 lbs. (1996 and Newer) # DL22439. This comes with replacement gears as well as the washer you need to replace on your current trailer jack.
view full answer... - Recommended Jack for Triple Axle Load Fast TrailerIf you're looking for a side mount swivel jack we have some great options for this. Mind you, the weight capacity of the jack only needs to be rated for the tongue weight of the trailer which is usually no more than 10% of the gross weigh for boats trailers. I recommend the Dutton-Lainson Bolt-On, Drop Leg Trailer Jack part # DL22320 which has a 2,500 lb capacity and offers up to a 28.5" lift.
view full answer... - Dutton Lainson Jack Recommendation to Replace One with 203960B LabelI spoke with my contact at Dutton-Lainson and he stated that the 203960B number that you pulled from your jack is a label number. That label was used on two different trailer jacks with a 1250 lb weight capacity, sidewind jack # 6814 and topwind jack # 6817. The closest sidewind jack we have would be the Dutton Lainson part # DL22320.
view full answer... - What is the Minimum Trailer Frame Height Dutton-Lainson Trailer Jack, # DL22320 Will FitTheoretically, the height of the trailer frame could be anything over 2 inches tall for the Bolt-On, Drop Leg Trailer Jack, # DL22320. The vertical center to center distance between holes is 1 inch. The gap between the first set of holes and second set of holes is 1-1/2 inches. The minimum trailer frame height would have to be 2 inches.
view full answer... - What is the Length of the Handle for Dutton Lainson Bolt-On, Drop Leg Trailer Jack, # DL22320I went out to the warehouse and measured the handle on Bolt-On, Drop Leg Trailer Jack, # DL22320. It is 8-1/2 inches long and sticks out 4-1/4 inches. The jack has an overall height of 25-1/4 inches when fully retracted, and a height of 38-1/2 inches when fully extended. From the top mounting hole to the ground when fully retracted it measures 10-1/4 inches. The mounting holes are 5-1/2 inches apart on center from left to right.
view full answer... - Replacement Parts for Dutton Lainson Trailer JackWe do offer both replacement parts and complete Dutton Lainson trailer jacks. All complete jacks can be view by clicking on the linked page. All Dutton Lainson jack replacement parts can be viewed by clicking on the other featured link. You can use the filters on the pages to select your type of jack and the type of replacement part you need, such as caster wheel # DL22414 that fits their a-frame jack # DL22530. I checked with Dutton Lainson for your part number 203960B but this was not...
view full answer... - Replacing Swivel Jack with Drop Leg Jack on Boat TrailerI have a solution for you, but we do not carry an adapter like you mentioned to mount a square tube jack to your existing winch stand. The best option for your set-up may be to use a jack like the Pro Series Square Jack with Footplate # PS1400850383. Then, using a sheet of metal drill the bolt holes to match the existing holes in your trailer. Another option is to try and find a drop leg jack that matches the mounting dimensions on your trailer. One option for a drop leg jack is the...
view full answer...
- Bolt On Trailer Tongue Jack Capable Of Fitting a 6" Tall FrameFor a 6" tall frame I recommend the ARK Xtreme Off-Road Swing-Up Trailer Jack # ORJW750BD as the Dutton-Lainson # DL22320 will only fit a trailer frame up to 5" tall. The ARK jack is rated for up to 1,650lbs capacity and fits trailer frames up to 6" tall and 2" wide. It uses dual wheels allowing you to position the trailer in tight areas.
view full answer... - Solution for Needing to Install 2,500 lb Trailer Jack on Trailer with 6 inch Tall FrameI really wish we had a bolt on solution but the tallest frame dimension we have a bolt on solution for is 5-1/2 inches like the Dutton Lainson part # DL22320. Only solution would be to weld the jack to the trailer.
view full answer... - Replacement Drop Leg for Dutton-Lainson Bolt-On, Drop Leg Trailer Jack - Sidewind - 2.5K DL22320It sounds like you are talking about the drop leg part of Dutton-Lainson Bolt-On, Drop Leg Trailer Jack - Sidewind - 2,500 lbs Item # DL22320. To replace the drop leg you can use Replacement Drop Leg for etrailer and Ram Square Direct Weld Jacks - 3K Item # TJD-5000-FT. I have linked a video review of this leg for you.
view full answer... - Recommended Sidewind Bolt-On Trailer Jack For 2,800 Lb TrailerThanks for all of the information you provided. It really helps when we make a recommendation that will work best for you. Based on the information you gave I recommend the etrailer Square, Fixed-Mount Marine Jack, part # MJSQ-2500B. This jack has a weight capacity of 2,500 lbs. Another jack I recommend is the Dutton-Lainson Bolt-On, Drop Leg Trailer Jack, part # DL22320. This also has a 2,500 lb weight capacity.
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Expert Research:
Lori W
Installed by:
Andrew K
Installed by:
Cole B
Updated by:
Lindsey S
Updated by:
Adele M
Updated by:
Mike S
Video by:
Jonathan Y
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Brooke M.
7/21/2023
I am so sorry, that is so frustrating. I checked and it looks like our customer service team is already on this and will be sending you the missing parts!