Bolt On Trailer Tongue Jack Capable Of Fitting a 6" Tall Frame

Question

Question:

Hi there, I have trailer with 6inch frame is this jack good for that frame?

asked by: Pietro I

0

Expert Reply:

For a 6" tall frame I recommend the ARK Xtreme Off-Road Swing-Up Trailer Jack # ORJW750BD as the Dutton-Lainson # DL22320 will only fit a trailer frame up to 5" tall. The ARK jack is rated for up to 1,650lbs capacity and fits trailer frames up to 6" tall and 2" wide. It uses dual wheels allowing you to position the trailer in tight areas.

expert reply by: Bud M

0

Answer 1

Hi Sebastian, While the Trailer Valet #TV34FR won't fit a 6" tall trailer frame (it only fits frames up to 3-3/4" wide x 4-3/4" tall), there is a bolt-on jack that does: - Fulton Boat Trailer Jack w/ Footplate #HD50000101 The…

view full answer...

Answer 2

The only bolt-on swivel jack we have that works with 6" tall trailer frames is the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211. The Trailer Valet has a 500 lb tongue weight capacity and works with frame rails up to 2-3/4"…

view full answer...

Answer 3

Do you see the white plastic piece in the shape of a U in the picture that you sent me? You will need to pull that piece out away from the harness to release it from the rest of the 7-way. Check out the video I attached and skip to the 3:25 mark to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Hey Matt, Furrion typically has 4 wires running to their thermostats and the Chill Cube Thermostat #LC74DX is no exception. The harness you see with the thermostat would plug into the Chill Cube's controller and has 4 wires to extra wire to to…

view full answer...

Bolt On Trailer Tongue Jack Capable Of Fitting a 6" Tall Frame

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching