Hitch Recommendation for a 1975 Ford F250 Crew Cab with a 34 inch Frame

Question

Question:

I am looking for a trailer hitch for my 1975 Ford F250 4th High boy with 34inch frame. Can you recommend any that would fit?

asked by: Douglas E

1

Helpful Expert Reply:

Yes, the Curt Hitch part # 13028 would work on your 1975 Ford F250 with a 34 inch frame. I confirmed this with Curt. I attached install instructions for you to check out also.

For trailer wiring you would want the Draw Tite Wiring Harness part # 18252.

For a ball mount, hitch ball, and pin and clip, I would recommend the etrailer Ball Mount Kit, part # 989900. This is a kit which includes 2 ball mounts, a 1-7/8 inch ball, 2 inch ball, and a hitch pin and clip.

expert reply by: Jameson C

1

Answer 1

When used with the #A45GB grommet, a 4-1/2 inch diameter hole is needed to flush-mount a 4 inch taillight.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 7

Hi Mike; based on your frame measurement it sounds like you have the standard or step bumper model of the 1992 F-250. The Curt #14001 is confirmed to fit this version of the pickup. If you want to be sure you can measure between the mounting holes in…

view full answer...

Answer 8

I spoke with my contact at Curt and he put together a chart that has all of the dimensions of the hitches you referenced.

view full answer...

Answer 9

Hey Chris, The Curt Trailer Hitch Receiver part #14001 will fit your 1986 Ford F-150 just fine! It's intended for models that have a standard or step bumper and isn't compatible with models that have a rollpan bumper. It fits Ford picks ups…

view full answer...

Answer 10

When measuring the frame width on a vehicle, you will need to measure from the outside of one frame rail to the outside of the other frame rail. It sounds like you have the 37-1/4 inch frame on your 1983 Ford F-100. The Curt Class IV 2 Inch Hitch,…

view full answer...

Answer 11

Curt Class V hitch #C15300 is a confirmed fit on your 1987 Ford F-150. To help you determine if it will be compatible with your skid plate I went to our warehouse and took a measurement of the hitch to find out the distance from the mounting brackets…

view full answer...

Answer 12

The distance from the front hole to the middle on the #14001 is 5.2". From the middle to the rear hole is 4.04" and from the front hole to the rear hole is 9.2". The distance across for each set of mounting holes is 36".

view full answer...

Hitch Recommendation for a 1975 Ford F250 Crew Cab with a 34 inch Frame

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching