Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting
Item # 154-792-118158
Our Price: $189.93
Confirmed to Fit
2004 Ford Escape
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
This item qualifies for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (55)
- Q & A (0)
- Photos
2004 Ford Escape - Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting
- Diode Kit
- Splices into Vehicle Wiring
- Tail Light Mount
- Universal
- Roadmaster
Connect your towed car's lighting system to your RV's to get the brake lights and turn signals required for towing. Designed for use with Ford Escapes that have separate brake and turn signals. 4-Pole flat loop and wiring converter included.
Features:
- Connects your RV's tail, brake and turn signal lights to your towed vehicle's lighting system
- Designed for use on towed vehicles that have a 3-wire system (separate brake and turn signals)
- Prevents electrical feedback and the damage it can cause to your towed car's electrical components
- Includes tail light converter to adapt your RV's 2-wire system (combined brake and turn signals) to work with the towed car's 3-wire system
- Contains everything you need to wire your car for flat towing
- 6 Hy-Power diodes
- Tail light converter
- 30' Long strand of 4-wire electrical cord
- 6' Long cord with 4-way flat connectors - both vehicle and RV ends
- Ring terminal and wire connectors
- 3' Long split-wire loom
- Limited Lifetime Warranty
Specs:
- Max amperage: 85 amps
- Max voltage: 24 V
Note: If your RV has separate brake and turn signal lights, you do not need to install the included tail light converter. However, you will need to replace the 4-way vehicle-side connector with one that is capable of carrying the separate signals.
The diagram below shows the installation of the 6-diode tail light wiring kit on a towed vehicle (or dinghy) that has separate turn signals (typically amber) and red brake lights. This kit will most often be used with a motor home that operates off of a 2-wire system wherein the brake lights do the flashing for the turn signals. The included tail light converter (118158) is used to convert the combined brake and turn signal lights to separate ones to match those of your towed vehicle.
154 and 792 Roadmaster Universal Wiring Kit with 6 Hy-Power Diodes and 118158 Tow Ready Tail Light Converter
Installation Details
Customer Satisfaction Score:
87% were satisfied with this product
13% of customers were not satisfied
- etrailer mistake
- Wrong item was ordered
- Did not fit
Customer Reviews
Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting - 154-792-118158
Average Customer Rating: 4.8 out of 5 stars (55 Customer Reviews)
Connect your towed car's lighting system to your RV's to get the brake lights and turn signals required for towing. Designed for use with vehicles that have separate brake and turn signals. 4-Pole flat loop and wiring converter included.by: Chris B03/25/2015
Subaru Outback Wagon
In ordering the parts I got a little confused as to exactly which kit I needed. My motorhome has combined brake/turn signal lights & the car ('03 Subaru Outback) has separate brake/turn/parking lights. Thought I needed the 6 diode kit (which I ordered) until I had all the parts here & read through the instructions for the umpteenth time (BEFORE cutting anything) & then realized what they were doing. Turns out all I needed was the 4 diode kit. Sounds like there won't be any problems returning the unneeded parts since they were never installed. Great service there!
Took a lot apart in the back of the car because of the lack of space behind the tail light assemblies, but it all comes apart pretty easily. Also allowed me to route the wiring along side the stock harness. Have a bunch of 1/2" split loom here & used it.
Thought I would have lots of wire left over, but I actually had to splice 2 cut offs to make a jumper long enough to get from 1 side of the car to the other. Glad the car wasn't any longer & I didn't have to make up 2 jumpers as with some of the kits!
Hardest part was finding a hole in the firewall & getting the harness routed under the dash so as to not tangle with the pedals, etc. I just don't flex like I used to.
Everything works fine although it was NOT a "5 minute job".
by: Rich L.03/05/2013
Chevrolet Volt
The diodes and wiring are good and worked well. But the 118158 converter produced a 3.5 volt drop such that the brake lights were as dim as the tail lights. And when a turn signal was triggered the brake lights dimmed even further. I ended up stringing a separate brake wire through the car and re-wiring my truck with a 5-wire connector.
by: Jerry B.08/04/2013
2013 Honda CR-V
Prompt deliver of product. We haven't gotten this part of our project installed, we are still watching YouTube videos and other info on procedure. Had very little difficulties installing base plate on our 2013 CRV this should go well also. Our lights are a little more complicated but once we figure out how to actually wire to them every thing we've learned so far is very straight forward.
by: Dale H06/26/2020
2013 Honda Fit
An ingenious system that enables a combined break and turn signal set up on your RV to properly operate the separate turn signal / brake setup of your toad. Beautiful!
Dale H.
6/28/2021
Have been using the brake and turn signal system for over a year now, and it is still working flawlessly!!
by: Christopher03/14/2018
2012 Ford Five Hundred
I used this wiring kit on a 2012 Fiat 500 Sport. All of the components worked as advertised and I am really pleased with the result. I used the 6 diode kit so the FIAT's turn signals would work the same when it's being towed as when it is driven.
This was my first light wiring kit installation and it was quite a challenge on the small FIAT to fish the flat cable from the rear of the car to the front. I ran it along the drivers side - over the rear wheel well, along the rocker panel, and up over the front wheel well. The wheel wells were the most difficult part of the job. Running the cable from driver's side to passenger side along the rear bumper and running it from the front wheel well to the front of the car and installing a connector were straightforward.
One problem I ran into is the female disconnect terminals supplied with the kit that are used to connect wires to the diodes anticipated a thicker wire (16-14 AWG) than what the FIAT uses. A quick trip to a close by big box store was all that was needed to find the same connectors for a thinner gauge wire (22-18 AWG). You still use the supplied disconnect terminals with the flat cable connections to the diodes.
by: John J06/12/2016
Honda
I bought this wiring kit because I wanted to wire my 2013 Honda CRV myself. E-Trailer has a video that is helpful in its installation . What I later found out was you need to route the wires through some covers underneath the vehicle and unless you have some means to raise the vehicle pretty high that routing will be difficult. I went to the Honda dealer and several other auto places and no one would install this kit for me because of liability reasons so now I have a product of question. I ended up at a friends garage who had a lift and we routed the wire from side to side and from front to back in about 20 minutes. Once secured in place I took the car home to finish the diode installation. Using the video it was easy to install. The only problem I had was putting the rear tai lights back in. You will need the separate the diodes as the space between the body and light housing is very close. Other than that everything worked out well.
by: ALEX A11/08/2016
The wiring works great, I got more in the KIT than I could possible use and I am sure I had to pay for the extras, but I got what I needed and am very happy.
Alex A.
11/8/2017
it is doing great
by: Bill02/05/2018
Toyota Tacoma
I used the wiring harness on my Tacoma pickup in preparing to tow it behind our 40’ motorhome. The harness went on easily from the front grill to the rear lights, where I soldered and heat wrapped each connection. The instructions were ample and easy to follow.
It’s been a year since the installation, and the wiring has worked flawlessly!
by: Jean C07/24/2019
Honda Civic
The Roadmaster Wiring Harness was installed easily by our mechanic and works perfectly with our Civic and RV. I'm certain we will use etrailer.com for our new dinghy towing requirements!
by: David10/28/2017
2010 Suzuki Grand Vitara
A great product. Installed easily. Previous wiring experience would be good for somebody wanting to use this.
It has performed flawlessly over the past year. I’d recommend it.
David
10/28/2018
Fantastic. No problems at all. Works as required every time I plug in.
by: Jerry07/29/2021
Ford Ranger
Install on a 2020 Ford Ranger. The product was excellent. The only problem I had was trying to remove the nuts holding the front bumper on. Ford has these bolts embedded in a hard plastic frame that spaces the three bolts on each side. In trying to remove the nuts I got them started then they would neither come on off nor reinstall. The nuts were spinning the bolts. After thinking about the fix I was in I decided to cut the factory bolts off and replace them with 1/2" x 1 1/2" bolts with fender washers. I tried a sawsall with a metal cutting blade and the bolts ate the teeth right off. I put on a Milwaukee thick metal cutting carbide tooth blade and that did the trick. Other than that, which is Ford's fault, everything went as the etrailer videos showed. If you are doing this make sure to spray the exposed bolt threads with WD-40 or something like before you try to remove the nuts.
by: Ron B05/23/2017
2015 Fiat 500
The kit contained all you need to wire lights on a Fiat. The instructions were clear and concise. Excellent product and service as usual for etrailer.
Ron B.
5/25/2018
After one year this kit is still doing its job flawlessly.
by: Rich B.06/02/2012
2012 Kia Sportage
This harness was an excellent choice. It took about an hour and fifteen minutes to install. Everything is spelled out for you in the instructions and if all else fails, watch the online video. The hardest thing was removing the tail light on the Sportage. I has a ball joint connection that forces you to pull harder than you think you should. I was afraid I would break the light. But it popped out and the rest was easy. Very complete and works great! The connections fit like factory. Very Pleased.
by: Dale05/06/2016
This is my second purchase of wiring kit for towed vehicle I have bought from Etrailer. I had some questions and Etrailer was able to answer every question I had. I will go back to Etrailer next time I need products such as this.
by: Danny07/05/2014
2013 Chevrolet Sonic
I found the product to be of very high guality. I did not supply pictures as I would need to remove my taillights again. I had to covert a motor home that did not have separate turn signals to a Sonic that did. The materials supplied allowed me to just that. I do have two other comments-The instructions showed the wires on the car on the passenger side which is opposite from the Sonic and most others I would think. I had to reverse my thinking to do the correct procedure. Also, could you not supply unit specific instructions if the towing vehicle lighting arrangement and the towed vehicle was identified. This would eliminate the extra parts that I did not need and help the customer complete the task. Other than that, very good product. I guess it is better to have extra parts ratter than not having enough but I just thought this might cut the cost for some applications.
by: John D07/29/2021
Was skeptical about using with led tail lights,but it all went well. The installation videos are spot on. After one year and about 12k miles traveled, no problems. My vehicle is a 2020 Ford Ranger.
by: Wayne06/06/2015
Product arrived on time.Online videos very well done.Katie D. provided excellent customer service on all the parts ordered.
Wayne S.
6/11/2016
very happy with product still working without any problems
by: James04/17/2021
Works as advertised. Design of these wiring kits is based on converting the common 3 bulb brake/turn signal systems to a 2 bulb system. This makes them unnecessarily complicated.
by: only1jerry11/05/2016
2005 Subaru Forester
I did a lot of research before buying. etrailer's prices and support are above average. I ordered the Roadmaster 913-1 baseplate, Falcon-2 towbar and 154 universal lighting kit. I was completely surprised by the fast shipping, all parts arrived 3 days before I expected AND the shipping was free!
Before I ordered I talked with etrailer support to ensure I ordered the correct parts. They were knowledgeable and helpful.
by: Dave G.07/28/2015
2008 Honda Fit
Very complete, hi quality, reasonably priced kit for lighting my "toad". If you have combined lights on your RV and separate lights (brake and turn) on your "toad", this is the kit.
by: Mike03/29/2017
Nice set up. Instructions were spot on. The hardest part of the installation was removing car interior panels to get to the wiring. Would definitely recommend this product.
by: Dale P03/20/2019
Ford
I ordered a towbar and accessories through the Internet site. It was very easy and also very informative. The supplies were ordered and I receive them in a couple of days. It was a great price and I did much research before I ordered. We are planning to install the towbar on our Ford C-Max and tow it with our phoenix cruiser 3100.
by: Denny K.07/14/2016
2014 Fiat 500
a little bit hard to get all wiring in, because I want the wiring not to be apparent and not exposed to harsh weather( snow, salt ,etc). But this setup is ideal, works perfectly and very quick when you connect your car the the motorhome.
by: Kevin 04/27/2021
Contained everything I required except the independent stop light switch.
by: Greg R.12/18/2016
Customer service was the best. Product delivered as expected. I recommend this wiring package. My towing safety comes first and Etrailer delivered.
25
55
Show More Reviews
See what our Experts say about this Roadmaster Tow Bar Wiring
- Tow Bar Wiring Recommendation for a 2002 Chevy TrackerWhat you need for your 2002 Chevy Tracker is tow bar wiring to allow a tow vehicle to control it's taillights as it is being towed. For that you would want the Roadmaster diode kit part # 154-792-118158 that has been confirmed as a fit for your Tracker. I attached an install video for you to check out as well.
view full answer... - Recommended Equipment for Flat Towing 2007 Honda Pilot 4WD Behind RVAccording to my research, your 2007 4WD Honda Pilot is capable of being flat towed, but Honda has some very exact instructions that need to be closely followed to prevent damaging the vehicle, so please consult your owner's manual. The Roadmaster # RM-522 and the # 1550-1 base plate would be compatible with your Pilot. The 6 diode wiring kit you mentioned, part # 154-792-118158 would also work fine. The # RM-643 safety cables, the # RM-055-3 Tow Bar Cover and the # SM99251 Stay In Play...
view full answer... - Parts Needed to Flat Tow a 2010 Volkswagen Jetta Sedan Behind a Motor HomeBlue Ox gives base plates # BX3823 an installation rating of 3. The installation rating is a rough measure of the time required for baseplate or bracket installation by a trained installer. These numbers can be used as rough suggested installation time by a trained installer. The first installation of a particular baseplate, and installation by untrained individuals will likely increase installation time substantially. It is strongly recommended to have them professionally installed....
view full answer... - Flat Towing Setup Recommendation for a 2013 Honda CR-VFirst let's start with a base plate kit for your 2013 Honda CR-V. For that you would want the Blue Ox Base Plate kit part # BX2258. The most popular tow bar we offer that would work great with this base plate kit is the Blue Ox Alpha part # BX7380. This tow bar has telescoping arms that will make connection and disconnection possible on unlevel terrain. These are much easier to use than the fixed arms tow bars. This comes with safety cables as well. For lighting you can use the diode...
view full answer... - Tow Bar Lighting Recommendation for a 2007 Honda AccordI wish we had tow bar wiring that was plug and play for your 2007 Honda Accord, but the best option I can make for your vehicle that won't require any splicing would be a magnetic kit like the part # C6304, or your other option would be a diode kit that would require quite a bit of splicing like the part # 154-792-118158. I attached a couple help articles on tow bar lighting for you to check out as well.
view full answer... - How To Use a Blue Ox Rangefinder II Tow Bar On a 2013 Ford C-MaxYes, in order to reuse your Blue Ox Rangefinder II Tow Bar 4322 you will need the Blue Ox Rangefinder II or III Tow Bar to Roadmaster Base Plates Adapters part # RM-037. This adapter kit allows you to use the Blue Ox Rangefinder II Tow Bar with a Roadmaster Crossbar-Style Base Plate Kit. The correct Roadmaster Crossbar-Style Base Plate Kit for your 2013 Ford C-Max is part # 524432-1. There are not any mounts available for the Blue Ox Rangefinder II Tow Bar to use with a Blue Ox Base Plate...
view full answer...
- What Items Are Needed To Flat-Tow 2014 Ford C-MaxThere are a few items needed when flat-towing your C-Max. You will need safety cables like part # RM-643 and tow bar lighting like part # 154-792-118158. I have attached a link to an installation video for the wiring on a C-Max. You will need a stop light switch part # RM-751459. This ensures the brake system is functioning correctly. You may want to to check the owner's manual under Recreational Towing to see if there are any restrictions or conditions that need to be met when you...
view full answer... - Is Brake Lite Relay Required for Use with 6-Diode Tow Bar LightingWith a 6 diode tow bar lighting kit like the # 154-792-118158 you would never need to use a Brake Lite Relay part # RM-88400. The Blue Ox kit you referenced would not be necessarily a 6 diode kit so it would not be what you need unless you wired it up like a 6 diode kit.
view full answer... - Parts Needed to Flat Tow a 2013 Ford ExplorerYes, we can help get you set with everything needed to flat tow your 2013 Ford Explorer with the 2017 Thor Miramar. There's at least 5 items needed for a proper flat tow setup - base plates, tow bar, safety cables, tail light wiring, and a supplemental braking system. The items you've listed are options confirmed to fit your Ford Explorer. Base Plate - Blue Ox Base Plate Kit, # BX2632 Tow Bar - Blue Ox Acclaim Non-Binding Tow Bar, # BX4330 (includes needed safety cables) Supplemental...
view full answer... - Are Roadmaster Kit Diodes and Wiring Converter for Isolated Stop Lamp Available Individually?The Vehicle to Vehicle Tail Light Converter # 118158 is absolutely available apart from the Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting # 154-792-118158. Then for the additional diodes you need beyond what you currently have you will use the Roadmaster Hy-Power Diode - (Qty 1) # RM-790 or package of 2 # RM-792. The prices are on each product summary linked or on the individual product pages.
view full answer... - Compatibility of 1994 Honda Accord with Blue Ox Bulb and Socket Flat Towing Lighting KitAccording to Blue Ox, the 1994 Accord wouldn't have enough room in the taillight assembly to accommodate the extra bulb needed for the # BX8869 bulb and socket kit, so it wouldn't be a good fit for your Accord. A diode kit like # 154-792-118158 would be your best choice for a permanent lighting solution, if the magnetic lamps aren't working well for you anymore. I've linked you to some helpful articles about flat towing.
view full answer... - Parts Needed to Flat Tow a 2011 Mini Cooper Base ModelFor your 2011 Mini Cooper hardtop base model the correct Blue Ox base plate kit is the part # BX1307 which is a confirmed fit. Next you will need a compatible tow bar. The tow bar I recommend the most is the Alpha, # BX7380. This tow bar does include another item you will need, safety cables. I have linked a video review of the tow bar as well. Next you will need lighting. For lighting you have some options. If you want something that installs quickly and does not splice into the vehicle...
view full answer... - Parts Needed to Flat Tow a 2007 Honda Fit Behind a Motor Home with an Aventa Tow BarIn order to determine if your 2007 Honda Fit can be flat towed behind a motor home you will want to consult the vehicle owners manual. Since you have an automatic transmission you will need to use base plates # 521558-1. Blue Ox does not have a base plate kit for the automatic transmission models. You can still use your Aventa tow bar by using adapter # BX88178. If you need safety cables, use # RM-643. For a lighting solution I recommend kit # 154-792-118158. Most states now require...
view full answer... - Installtion of Towbar Wiring on a 2015 Chevrolet Malibu for Flat TowingDon't worry, I can help! According to Roadmaster the bulb and socket kit will not work for your 2015 Chevrolet Malibu but the universal wiring kit # 154-792-118158 will. It also states that since you have separate wiring that it is recommended to have two additional diodes which this kit includes. While magnetic lights are an option there should be no issue when installing the universal wiring kit to your Malibu. Some more helpful information I found about towing your Malibu is that...
view full answer...
- Is Cable to Connect Motorhome and Flat-Towed Vehicle Included in Diode Kit # 154-792-118158The Roadmaster Tow Bar Wiring Kit # 154-792-118158 that you referenced includes all required diodes, connectors and wiring to set up your Honda Fit for flat towing. The longest cable in the kit, the 30-foot flat connector harness, will run from the rear of the Fit up to the front of the car; it should be positioned near the center of the vehicle to avoid being pulled when the motorhome turns. This 4-pole is where the toad and motorhome will connect to each other. I have included links...
view full answer... - Parts Needed to Tow a 2009 Toyota Camry With a Fleetwood RevolutionIf your 2009 Toyota Camry has an automatic transmission, then it will require a tow dolly like the Roadmaster Tow Dolly, # RM-2050-1, that you referenced on our website. One advantage to using this tow dolly is that it already comes with brakes and lights which will minimize the amount of additional items you will need. In order to operate the electric brakes on this tow dolly, you will need to have a 6-Way round trailer connector on the motor home, and an electric brake controller. I...
view full answer... - Parts Needed to Flat Tow a 2003 Chevy Tracker behind a Motor HomeYou will need to look up a 2003 Chevy Tracker because Geo ended in 1997. For a 2003 Chevy Tracker you can use the Demco kit # DM9518079. For a compatible tow bar I recommend the Demco Commander # DM9511012. It is rated for 6,000 pounds and also includes another item you will need, safety cables. I have included a link to the installation instructions for you to view. Next you will need a lighting solution. If you will not be towing the Tracker very often I recommend a magnetic kit like...
view full answer... - Tow Bar Wiring Causes Lights Not to Work on 1992 Elite Motorhome and 1997 Jeep Grand CherokeeYou are just going to need the proper wiring kit. It sounds like there are a combination of problems that are leading to the failures. There could be short and ground issues causing the lights not to work and the converter to blow. First, lets look at what is going on with the motor home. If it has a trailer connector on it you will want to test it using a circuit tester such as # PTW2991. I have included a link to a help article that explains how to test it. If some of the circuits are...
view full answer...
- Parts Needed to Flat Tow a 2010 Honda Fit With a Class A Winnebago Journey 34We have everything that you will need to flat tow your 2010 Honda Fit with automatic transmission behind your Class A Winnebago Journey 34. The Roadmaster Falcon 2 Tow Bar, # RM-520, is a great idea and is one of our most popular tow bars that we sell. You may also be interested in the Falcon All Terrain Tow Bar, # RM-522, as well. I have attached installation instructions and video links for both tow bars for you to compare. The additional items that you will need are a base plate kit,...
view full answer... - Parts Needed To Flat Tow a 2015 Ford Fiesta Behind a Motor HomeA plug in tow bar lighting system is not available for your 2015 Ford Fiesta but there are other options that will work. You could use a magnetic light kit, # RM-2120, a bulb and socket kit, # RM-155, or a diode kit, # 154-792-118158. The magnetic light kit will be the most cost effective option and the least permanent. The diode kit is the most involved of the installations and requires splicing into the vehicle wiring for installation. The bulb and socket kit bypasses the vehicle wiring...
view full answer... - Towing Wiring Harness For Mercedes Sprinter 2500We do not recognize this connector that you have provided a picture for but we have a solution. We do not have an adapter to go between that plug and a 7-way connector. However you can create your own 7-way jack for your trailer to plug into. You will need to install a Tekonsha # TK22115 wiring harness that includes the 7-way connector for the back of your Sprinter. If you will be towing a trailer with brakes, you will additionally need the Tekonsha # 90195 brake controller. This installs...
view full answer...
- Recommended Complete System for Flat Towing a 2016 Hyundai AccentBased on what I can find, if you have a manual transmission you can Flat Tow a 2016 Hyundai Accent. If you have an Automatic Transmission, it will need to be towed with a dolly. I'd recommend the Roadmaster Tow Dolly with Electric Brakes - 4,250 lbs, # RM-2050-1, because it has some cool features like a deck platform that swivels 9 degrees for tight cornering. It includes all of the lighting and the 4 way connector, however a 7 way connector is required to activate the dolly's brakes,...
view full answer... - Parts Needed to Flat Tow a 2012 Toyota Tacoma with Roadmaster Stowmaster Tow BarYes, there is some drilling required to install base plates # 1175-3 on your 2012 Toyota Tacoma. I have included a link to the installation instructions to the right for you to view. These base plates are NOT compatible with the Roadmaster Stowmaster tow bar # RM-501. I recommend using the XL base plates # 1175-1. There is still drilling required but these base plates are compatible with the Stowmaster tow bar. You will also need safety cables # RM-643. The coiled design helps keep the...
view full answer... - Recommended Parts Needed To Flat-Tow 2013 Honda CR-VWhen you flat-tow your 2013 CR-V you will need 5 items. You need base plates, tow bar, safety cables, lighting for the CR-V, and most states now require a supplemental brake system. I have attached a link to a helpful article that explains flat-towing you can check out. I recommend Falcon All Terrain Tow Bar, part # RM-522. The adjustable arms on this tow bar allow you to easily attach and release your CR-V. That is the advantage over the Falcon tow bar, part # RM-520. Both of these tow...
view full answer...
Do you have a question about this Tow Bar Wiring?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Nicholas E
Test Fit:
Randy B
Expert Research:
Jackie C
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Sue W
Written by:
Lindsey S
Updated by:
Adele M
Updated by:
Rachael H
Updated by:
Wilson B
Updated by:
Hannah L
Updated by:
Isabelle B
Video by:
Andrew L
Video by:
Alan C
Video by:
Chris R
Installed by:
Cole B
Installed by:
David F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jerry B.
2/2/2015
So far, so good. Weve only towed the car one way from KS to Fl. Everything working great. Thinking about adding a receiver hitch but, will take it to the dealer as we sold our farm, and our tools and have the grandsons arent available to do the hard work.