Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
If you’re ready to move beyond sluggish or uneven drum brakes, this Kodiak kit delivers stronger, smoother stopping. The 13" one-piece hub-and-rotor assemblies fit 7,200-lb axles with #42 spindles and an 8 on 6-1/2" bolt pattern. Ceramic brake pads and a large 2-1/2" stainless steel piston give fast, responsive braking with a solid, controlled feel every time you stop.


Frequent freshwater launches or damp storage can eat through uncoated brake parts. The Dacromet coating on these hub-rotors, calipers, and brackets holds up to 300–400 hours of salt spray—comparable to galvanized steel. That means dependable protection against rust and corrosion even after repeated dunking or wet towing.

Long grades or heavy loads can build heat fast. These vented rotors dissipate heat quickly so pads last longer and braking stays consistent. The one-piece hub-and-rotor design also keeps water and debris out, preventing runout or uneven rotor wear for smoother braking over time.

This kit includes two Dacromet-plated hub-and-rotor assemblies with bearings, races, grease seals, E-Z Lube caps, wheel bolts, and lug nuts—everything required to upgrade one axle. With fewer moving parts than drum setups and no springs or cables to adjust, these brakes are easier to maintain and keep working reliably season after season.


Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi there, I'm Michael with etrailer.com. Today we're gonna take a quick look at this Kodiak 13 inch hub and rotor disc brake assembly set. This is going to allow you to upgrade your trailer from drum brakes to disc brakes so you can take advantage of the superior performance that comes along with having disc brakes on your trailer. Having the two brake assemblies here is going to allow you to upgrade a single 7,200 pound capacity axle with the number 42 spindles. Our rotors are 13 inches in diameter, and as you can see, we've got the eight on six and a half inch bolt pattern with these nine 16th inch diameter wheel bolts. So, this is going to work for your wheels that are 16 inches and larger.
We've got a dacromet finish on the hub and rotors and on the mounting brackets and it's gonna provide excellent rust and corrosion resistance with a 300 to 400 hour salt spray rating. We also have an e-coat on the calipers to provide adequate rust and corrosion protection with a 250 to 350 hour salt spray rating. So, these are gonna be great for your freshwater boat trailers, or even if you're gonna be going into the water quite a bit, these will hold up really well for you. If you are gonna be in saltwater or on heavily treated roads where there's gonna be a lot of interaction with salt, I would recommend going more with a stainless steel construction. Those are gonna hold up a little bit better for you, but if you're gonna be in the fresh water and in less corrosive environments like that, this will do a really good job for you, help things to hold up really well.
So, when you're looking at upgrading from drum brakes to disc brakes, you're gonna notice a huge performance improvement. These are going to do a great job at dramatically shortening your stopping distance. It's gonna provide smoother, more controlled braking than you're used to with your drum brake. So, it's gonna help keep your trailer from pushing and pulling. We've got ceramic brake pads that help to increase the stopping power and there is a large two and a half inch diameter stainless steel piston that provides fast responsive braking.
And then, in addition to improved performance, you're also going to have less maintenance with disc brakes over your drum brakes. So, it is gonna help save you time and money. Having the one piece hub and rotor assembly is gonna reduce the chance of uneven rotor wear. And we have a vented design here on the side that's going to help dissipate heat faster to prevent premature brake pad wear. These are a high quality automotive grade construction, so they are gonna be very long lasting for you.
So, again, it's gonna help save you time and money over your drum brakes. There's little springs that could potentially fail and have to be replaced on those sort of things that add up over time. So, the one caveat to upgrading to disc brakes is that disc brakes do require a higher line pressure than your drum brakes. So, you're gonna need to make sure that you have a hydraulic brake actuator and brake lines that are rated for 1500 PSI or higher, and that's pretty rare for trailers that are set up for drum brakes. So, that might take a bit to get that whole system converted over. If you don't already have a hydraulic brake actuator in the brake lines, we do sell those separately here at etrailer.com. Obviously, it's not included in this kit, so it's not gonna be everything that you need here, but this will provide the two dacromet plated cast iron hub and rotor assemblies with the eight pre-installed nine 16th inch diameter wheel bolts on each one. You're also going to get 16 of these nine 16th inch zinc plated steel lug nuts to hold your wheel in place. You'll get the two e-coded cast iron calipers, as well as the two dacromet plated ductile iron caliper mounting brackets. As you can see, these mounting brackets have the four whole brake flange configuration or the four bolt brake flange configuration, so it is gonna be very easy to get mounted on your axle. I do wanna point out that I've got these mounted on top just for display purposes. When you actually go to mount these, they will be mounted on the side. That side support design puts all the weight on the mounting bracket instead of on your bolts, so it helps your bolts last longer. You are gonna get four of these stainless steel caliper mounting bolts. We also have our inner and our outer races that are pre-installed here. Inside those races, we're gonna have our inner and outer bearings that are going to make sure that everything's rotating smoothly. This system is lubricated with grease, so you're going to have your two grease seals on the inside, and then, your two easy lube grease caps for the outside. And these do have those rubber plugs that can pop out, so you can more easily access your easy lube spindles to pump grease in there if you have those. Otherwise, just a grease cap that will allow, prevent any contamination in there, make sure that your grease is keeping everything well lubricated. So, like I said, if you are wanting to upgrade from drum brakes to disc brakes on your trailer or if you're just needing to replace the disc brakes on your trailer, these are gonna do a great job for you, especially with that dacromet finish. They are gonna hold up well for a lot of environments. So, that completes our look for today. Again, I'm Michael with etrailer.com. Thanks for watching.
Ratings & Reviews

Richard
12/3/2025
Nothing new which is good news, although I will replace the bearings sometime this winter with Timken. This is the stock brake for Morryde IIS and it work well enough. The China bearing are what it comes with, but in an effort to not have to worrywonder, Timken is my choice. Not sure about some of the complaints but other than cardboard not holding up to heavy metal mine were new and good. I believe sometimes returns and part get put in a box a second time and that screws everyone up. Not being an upgrade, I am not sure there is another choice even if I wanted it.

Frank
10/15/2025
I decided to go with the Kodiak set up and we couldn’t be happier with the service with them. I feel that the trailer stops around 40 better.

Nick S.
12/1/2025
I am sorry to hear about your experience with these brakes. We will reach out shortly and help resolve this for you.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.





Christopher
5/26/2025
No regrets and loving the product design.